SMT, PCB Electronics Industry News
  • SMTnet
  • »
  • Industry News
  • »
  • Seika Machinery, Inc. to Exhibit Green Technologies at the SMTA Dallas and Houston Expo & Tech Forums

Seika Machinery, Inc. to Exhibit Green Technologies at the SMTA Dallas and Houston Expo & Tech Forums

Feb 04, 2011

Seika’s new Solder Paste Recycling Unit enables approximately 90 percent of waste solder paste to be recovered as solder bar.

Seika’s new Solder Paste Recycling Unit enables approximately 90 percent of waste solder paste to be recovered as solder bar.

The Sawa Eco-Roll eliminates waste and saves money by reusing wiper rolls for printing machines.

The Sawa Eco-Roll eliminates waste and saves money by reusing wiper rolls for printing machines.

Sawa Ecobrid handheld and fully automatic low-VOC emission stencil cleaner.

Sawa Ecobrid handheld and fully automatic low-VOC emission stencil cleaner.

Seika Machinery, Inc., a leading provider of advanced machinery, materials and engineering services, will highlight green technologies at the upcoming SMTA Dallas and Houston Expo & Tech Forums. The SMTA Dallas Expo & Tech Forum is scheduled to take place Tuesday, March 1, 2011 at the Richardson Civic Center in Richardson, TX and the SMTA Houston Expo & Tech Forum is scheduled to take place Thursday, March 3, 2011 at the Stafford Centre in Stafford, TX.

Seika's new Solder Paste Recycling Unit enables approximately 90 percent of waste solder paste to be recovered as solder bar. The system provides a major decrease in disposal costs for factory waste, a reduction in CO2 emissions, and reduced costs for solder bar as a result of recycling waste. As an additional benefit, the recycling unit enables selection of manual mode and automatic mode using a touch screen panel.

Seika will feature the new Sawa Eco-Roll large roll model that cleans wiper rolls up to 24". The Sawa Eco-Roll eliminates waste and saves money by reusing wiper rolls for printing machines. In addition to providing a reduction in waste, use of the wiper roll cleaner results in reduced CO2 emissions in just 20 minutes.

Wiper rolls are widely used for under stencil cleaning to wipe off solder paste in the SMT printing process. Most of them are used only once, then are disposed of with other solder waste. Recycling wiper rolls not only reduces emissions but also reduces lumber usage. Additionally, tests have shown that repeated cleaning of wiper rolls does not compromise the performance when cleaning stencil apertures.

Seika also will highlight the new Sawa Ecobrid handheld and fully automatic low-VOC emission stencil cleaner. The cleaner provides up to a 66 percent reduction in CO2 emissions as well as a significant reduction in running costs. Additionally, the system cleans and dries in just five minutes

Sawa Stencil Cleaners are widely used in the Japanese electronics industry to ensure high yields when screen printing solder paste onto PCBs. Normal cloth wipe cleaning of stencils cannot completely remove solder paste especially in fine-pitch applications because a small amount of solder balls have a tendency to adhere to the corners of the apertures.

Seika also will highlight its new low-cost PCB McDry Electronic Drying Storage Cases, featuring new economy prices with the high performance and value that McDry is known for.

McDry units come in 1 and 3 percent RH models to comply with the strict standards required for proper storage of moisture-sensitive materials requiring ultra-low humidity levels.

Product literature also will be distributed for all of Seika Machinery’s products. For more information about Seika’s full product line, visit Seika at the SMTA Dallas and Houston Expo & Tech Forums or visit http://www.seikausa.com.

Seika Machinery, Inc. (SMI) is a subsidiary of Seika Corporation, Japan and member of the Mitsubishi Global Group. SMI provides electronics manufacturers with advanced machinery, superior materials and engineering services.

Aug 15, 2017 -

Seika to Bring the Industry’s Top Manufacturing Equipment to SMTAI

Jun 29, 2017 -

Seika Introduces Sayaka Twin Table PCB Router with Online Camera for Programming

May 03, 2017 -

Effectively Test Wetting Balance of Component Leads with the New MALCOM SWB-2 Dip Wetting Tester

Feb 23, 2017 -

Seika Recognizes Top Performing McDry Reps during APEX

Feb 01, 2017 -

New Bubble Washer System for Stubborn Flux Cleans Five Times Faster than Immersion Cleansing

Jan 11, 2017 -

Seika Machinery to Bring New Kawaski Dual Arm SCARA Robot to APEX

Jan 10, 2017 -

New SAWA Ultrasonic Squeegee Cleaner Presents New Solution for Lead-Free Pastes

Jan 09, 2017 -

Explore Industry-Leading Equipment from Seika Machinery at APEX

Sep 12, 2016 -

Seika Machinery to Bring a Modular Reflow Oven Profiling System to SMTA Guadalajara

Sep 08, 2016 -

Attend the SMTA Ambassador Reception during SMTAI

186 more news from Seika Machinery, Inc. »

Aug 19, 2017 -

See Latest Dispense Technology Demonstrations From GPD Global at NEPCON 2017

Aug 17, 2017 -

ZESTRON Americas Announces New Regional Sales Manager

Aug 17, 2017 -

SEHO Soldering Expert to Discuss Resource & Cost Efficient Wave Soldering at SMTAI

Aug 17, 2017 -

Libra Industries Announces Two 20-Year Service Awards in Q2 2017

Aug 17, 2017 -

Cirtronics Installs High-Performance X-ray Inspection Solution

Aug 17, 2017 -

Essemtec to Show New All-in-One Jetting / Placement System at SMTAI

Aug 17, 2017 -

Engineered Material Systems to Introduce New Conductive Adhesives for Stringing and Shingling Next-Generation Solar Modules at EU PVSEC

Aug 17, 2017 -

What is SMT and where to by SMT spare parts

Aug 16, 2017 -

ViTrox and KIC Establish Cooperation and Connectivity

Aug 16, 2017 -

Inovaxe Is Making Storage SMARTER – Visit Booth #915 at SMTAI

See electronics manufacturing industry news »

  • SMTnet
  • »
  • Industry News
  • »
  • Seika Machinery, Inc. to Exhibit Green Technologies at the SMTA Dallas and Houston Expo & Tech Forums
SMT Machines

PCB equipment