SMT, PCB Electronics Industry News

Seika Machinery Will Exhibit the Latest SMT Solutions at SMTAI

Aug 27, 2015

The RD-500V Rework Station features a two mega pixel full HD camera with a 19

The RD-500V Rework Station features a two mega pixel full HD camera with a 19" LCD display for easy visual alignment. It samples the data in very small intervals of 0.1 sec, allowing extremely accurate temperature control.

Seika Machinery, Inc., a leading provider of advanced machinery, materials and engineering services, will exhibit in Booth #707 at SMTA International, scheduled to take place Sep. 29 - 30, 2015 at the Donald Stephens Convention Center in Rosemont, IL. The Seika team will be available to demonstrate the following equipment: DEN-ON INSTRUMENTS CO., LTD. RD-500V Rework Station, UNITECH UC-250M-CV PCB Board Cleaner, MALCOM SPS Solder Paste Mixer and MALCOM Spiral Viscometer.

The RD-500V Rework Station features a two mega pixel full HD camera with a 19" LCD display for easy visual alignment. It samples the data in very small intervals of 0.1 sec, allowing extremely accurate temperature control. The RD-500V is equipped with powerful built-in 1000W heaters on both the top- and bottom-side, and an area heater that includes six quick heating 600W IR heaters. Precise profiling including detailed temperature curves can be executed with the ability to closely control up to 30 zones.

The UC-250M-CV Board Cleaner adds a dual cleaning feature using a combination of a brush roller with the silicone/adhesive cleaning rollers. The combination dual dust removal system assures better results than a single brush or adhesive roller system. The UC-250M-CV has the ability to clean the top surface of PCB even chip components attached on the bottom side. Additionally, the cleaner features an antistatic bar (ionizer) to neutralize static and prevent dust from collecting on the top surface of the PCB.

The MALCOM SPS Solder Paste Mixer is a non-contaminating mixer that utilizes pseudo planetary motion to stir the solder paste. The SPS-1 provides uniform paste consistency regardless of operator skill. The paste temperature rises due to friction, enabling control over the solder paste viscosity. Now, a solder paste can be pulled from the refrigerator and ready on the stencil, in 10 minutes.

The MALCOM PCU-200 Digital Viscometer features a patented spiral-pump sensor that provides quick, easy and repeatable measurements. It provides continuous measurement of newtonian and non-newtonian fluids with constant shear rate and shear time. Additionally, the system features automatic control of measurement according to JIS standards (PCU-203,205). Application includes solder pastes, thick film pastes, solder resists, liquid resists, inks, etc.

Also at the show, company representatives will highlight the MALCOM RCX-1 Reflow Monitoring System and Hioki Flying Probe among other equipment.

For more information about any of the advanced equipment from Seika Machinery, contact Michelle Ogihara at michelle@seikausa.com or visit www.seikausa.com.


Seika Machinery, Inc. (SMI) is a subsidiary of Seika Corporation, Japan and member of the Mitsubishi Global Group. SMI provides electronics manufacturers with advanced machinery, superior materials and engineering services.

Jun 29, 2017 -

Seika Introduces Sayaka Twin Table PCB Router with Online Camera for Programming

May 03, 2017 -

Effectively Test Wetting Balance of Component Leads with the New MALCOM SWB-2 Dip Wetting Tester

Feb 23, 2017 -

Seika Recognizes Top Performing McDry Reps during APEX

Feb 01, 2017 -

New Bubble Washer System for Stubborn Flux Cleans Five Times Faster than Immersion Cleansing

Jan 11, 2017 -

Seika Machinery to Bring New Kawaski Dual Arm SCARA Robot to APEX

Jan 10, 2017 -

New SAWA Ultrasonic Squeegee Cleaner Presents New Solution for Lead-Free Pastes

Jan 09, 2017 -

Explore Industry-Leading Equipment from Seika Machinery at APEX

Sep 12, 2016 -

Seika Machinery to Bring a Modular Reflow Oven Profiling System to SMTA Guadalajara

Sep 08, 2016 -

Attend the SMTA Ambassador Reception during SMTAI

Sep 01, 2016 -

Attend the 7th Annual SMTA Women’s Leadership Program at SMTAI

185 more news from Seika Machinery, Inc. »

Jul 25, 2017 -

CalcuQuote to Debut Purchasing Application for EMS at SMTA International

Jul 25, 2017 -

YINCAE TO EXHIBIT AT SMTAI 2017

Jul 23, 2017 -

PDR Americas Partners with Orr Marketing, Inc. in the Carolinas

Jul 23, 2017 -

Zuken Announces XJTAG DFT Assistant for CR-8000 PCB design suite

Jul 23, 2017 -

SMTA Welcomes New Board Members

Jul 23, 2017 -

SMTA International Technical Program Expands, Includes Research from HDPUG and AREA Consortium

Jul 23, 2017 -

Senator Ron Johnson Discusses U.S. Policy Priorities in Townhall Discussion with IPC-member Company, VirTex MTI

Jul 21, 2017 -

Epec Now Offering PCB Layout and Design Services

Jul 21, 2017 -

Help customer solve problems of 750L machine

Jul 19, 2017 -

Digicom Electronics Receives AS9100:2016 (RevD) Aerospace and ISO 9001:2015 Certifications

See electronics manufacturing industry news »

Seika Machinery Will Exhibit the Latest SMT Solutions at SMTAI news release has been viewed 524 times

PCB equipment

PCB machines