SMT, PCB, EMS Technical Articles

Corrosion Analysis

Jun 03, 2019 | ACI Technologies, Inc.

ACI Technologies was pleased to assist a customer by conducting elemental analysis on several assemblies displaying severe corrosion. Several board assemblies had failed in the field and exhibited areas of corrosion in close proximity to onboard components. The most common source of corrosion on electronic assemblies is residual flux. Fluxes are specific chemistries applied during the soldering process which improve the wetting of the solder to both the pad and component when forming the solder joint. They can be highly reactive chemicals that, if left on the assemblies, can lead to corrosion, electrical degradation, and decreased reliability. In the presence of moisture and electrical bias, flux residue can enable dendritic growth as a result of electrochemical migration (ECM)....

Publisher: ACI Technologies, Inc.

ACI Technologies, Inc.

ACI, an authorized IPC Training Center operating the National Electronics Manufacturing Center of Excellence providing analytical testing, manufacturing and repair services to the electronics industry.

Philadelphia, Pennsylvania, USA

Consultant / Service Provider, Standards Setting / Certification, Training Provider

The Power Packaging Laboratory at ACI Technologies

May 31, 2019 | ACI Technologies, Inc.

Microelectronics is the manufacture of systems built from extremely small electronic components. In today’s electronic world, devices must be portable, equipped with wireless technology and are driven by size, weight, power, and cost (SWaP-C). These system level drivers are crucial to all current and future electronic applications from personal computers and cellular telephones to military-fielded hardware, biomedical instrumentation, and space-flight hardware....

Publisher: ACI Technologies, Inc.

ACI Technologies, Inc.

ACI, an authorized IPC Training Center operating the National Electronics Manufacturing Center of Excellence providing analytical testing, manufacturing and repair services to the electronics industry.

Philadelphia, Pennsylvania, USA

Consultant / Service Provider, Standards Setting / Certification, Training Provider

SMT Component Reliability for RF Applications

May 31, 2019 | ACI Technologies, Inc.

ACI Technologies (ACI) characterized the reliability of surface mount RF components. The RF frequency band of interest was the X band (10.7 to 11.7GHz). A two pronged test for reliability of circuit card assemblies (CCA) was designed for both extreme thermal cycling and vibration. The rapid thermal cycling and extreme vibration testing simulates the total stress encountered by the assembly over the life of the product but accomplishes it in a relatively short period of time. In order to perform the reliability testing, a test vehicle consisting of a printed circuit board with test structures and components, was designed, fabricated, and assembled at ACI....

Publisher: ACI Technologies, Inc.

ACI Technologies, Inc.

ACI, an authorized IPC Training Center operating the National Electronics Manufacturing Center of Excellence providing analytical testing, manufacturing and repair services to the electronics industry.

Philadelphia, Pennsylvania, USA

Consultant / Service Provider, Standards Setting / Certification, Training Provider

COTS Cooling

May 31, 2019 | ACI Technologies, Inc.

ACI Technologies (ACI) is working on a project where one of the challenges is removing a large quantity of heat from audio amplifier circuits. This challenge is further complicated in that the heat generating circuits are located in a rack mounted box that needs to be shielded from electro-magnetic interference (EMI). Mechanically, this means that there cannot be open passages into the rack mounted box. We will first review the basic types of cooling available as commercial off-the-shelf (COTS) systems for the electronics industry, then discuss the pros and cons of each for different applications, and finally reveal the criteria and solution for the ACI project....

Publisher: ACI Technologies, Inc.

ACI Technologies, Inc.

ACI, an authorized IPC Training Center operating the National Electronics Manufacturing Center of Excellence providing analytical testing, manufacturing and repair services to the electronics industry.

Philadelphia, Pennsylvania, USA

Consultant / Service Provider, Standards Setting / Certification, Training Provider

Thermal Interface Materials Testing

May 30, 2019 | ACI Technologies, Inc.

There exists a need to efficiently remove heat from power electronics within power systems to enhance performance. Thermal management is a critical function to that operation. Reducing the junction temperature of semiconductor power electronic devices enables them to operate at higher currents. Lowering operating temperatures reduces the thermal stress on electronic devices, which improves efficiency and reduces failures. To improve the heat removal process, the current heat transfer design of a power system has been analyzed and a variety of thermal interface materials (TIMs) and cold plate technologies have been evaluated. This paper will review some of these results....

Publisher: ACI Technologies, Inc.

ACI Technologies, Inc.

ACI, an authorized IPC Training Center operating the National Electronics Manufacturing Center of Excellence providing analytical testing, manufacturing and repair services to the electronics industry.

Philadelphia, Pennsylvania, USA

Consultant / Service Provider, Standards Setting / Certification, Training Provider

Identifying Battery Load Qualification Test Parameters

May 30, 2019 | ACI Technologies, Inc.

In a previous Tech Tip (see Battery Selection for Electronic Systems), considerations were discussed for selecting an appropriate battery for an application. After selection, testing should be performed to confirm that the battery can provide the power required for the specific application. Some battery definitions should be understood when discussing power load qualification testing of batteries....

Publisher: ACI Technologies, Inc.

ACI Technologies, Inc.

ACI, an authorized IPC Training Center operating the National Electronics Manufacturing Center of Excellence providing analytical testing, manufacturing and repair services to the electronics industry.

Philadelphia, Pennsylvania, USA

Consultant / Service Provider, Standards Setting / Certification, Training Provider

BGA Reballing

May 30, 2019 | ACI Technologies, Inc.

In the current economic environment, the ability to reuse ball grid array(BGA) components that have failed due to solder defects may be an efficient way for electronics manufacturers to reduce costs. Cost may not be the only driving factor in the decision to engage in this recycling practice. The increasing demands placed upon the complexity of microprocessors and integrated circuits (ICs) has decreased the availability of some components, and increased their lead time. Because of this, reballing may provide a means to meet schedule, reduce rework turn-around time, and give a manufacturer a decisive advantage over other companies in an ever increasingly competitive market. This article will discuss the process of reballing BGA components (Figure 1), examining preparation (the preform method, the screen method), and cleaning and bake-out....

Publisher: ACI Technologies, Inc.

ACI Technologies, Inc.

ACI, an authorized IPC Training Center operating the National Electronics Manufacturing Center of Excellence providing analytical testing, manufacturing and repair services to the electronics industry.

Philadelphia, Pennsylvania, USA

Consultant / Service Provider, Standards Setting / Certification, Training Provider

Hand Printing using Nanocoated and other High End Stencil Materials

May 29, 2019 | Bob Wettermann

There are times when a PCB prototype needs to be built quickly to test out a design. In such cases where it is known early on that there will be multiple iterations or that a "one and done" assembly will be made that there will be some SMT assemblers who choose to hand print solder paste onto the board using a "frameless" stencil. In such cases where hand printing is used, the consistency of the printing technique has typically been in question. Furthermore, the effectiveness of both the nanocoatings as well as the higher end stainless steel materials, which have been heretofore studied in controlled printing environments, will be evaluated for their impact on the hand printing process.</p><p>The purpose of the study was to determine the effectiveness of select nanocoating materials as well as certain high end stainless steel stencil materials as they relate to the manual SMT printing process. A variety of nanocoatings were applied to SMT metal stencils and solder paste volume measurements were taken to compare the effectiveness....

Publisher: BEST Inc.

BEST Inc.

BEST offers professional rework, repair and prototype builds of PCBs. Our expertise is on BGA rework and QFN rework. Our experienced instructors teach professional soldering classes as we are an IPC certified training center

Rolling Meadows, Illinois, USA

Consultant / Service Provider, Manufacturer

The prerequisites for tomorrow's technologies

May 29, 2019 | Scheugenpflug

Scheugenpflug focuses on e-mobility and autonomous driving and, with its high-quality dispensing solutions, is accompanying an imminent turn of events in the growth field of mobility....

Publisher: Scheugenpflug Inc.

Scheugenpflug Inc.

Producer of bonding, dispensing and potting solutions with outstanding expertise in automation. As part of the Atlas Copco Group, we have a worldwide sales & service network and access to the Group's extensive technology portfolio

Kennesaw, Georgia, USA

Manufacturer

Battery Selection for Electronic Systems

May 29, 2019 | ACI Technologies, Inc.

Battery selection should be considered early during the design phase of affordable electronic systems. The important choice of an appropriate battery can reduce system acquisition costs and keep logistics support costs down for the life of the system....

Publisher: ACI Technologies, Inc.

ACI Technologies, Inc.

ACI, an authorized IPC Training Center operating the National Electronics Manufacturing Center of Excellence providing analytical testing, manufacturing and repair services to the electronics industry.

Philadelphia, Pennsylvania, USA

Consultant / Service Provider, Standards Setting / Certification, Training Provider