Electronics Manufacturing Technical Articles

Measuring Conformal Coating Thickness

Jul 21, 2015 | Roger Plough

Achieving an even coat at the right desired thickness is a major challenge when it comes to applying conformal coating to a Printed Circuit Board (PCB). Applying a coating too thin will ultimately render the electronic assembly vulnerable to potential environmental risks therefore defeating the purpose of the coating. Apply the coat too thick, and it could leave the electronic specific components non-functional therefore destroying the electronic assembly entirely. Coating thickness must meet quality specifications. Measurements for coating thickness may be taken while film is dry or wet. Once measurements are recorded, thickness is compared to quality specifications and fluid dispensing automation machinery is calibrated as necessary. There are a handful of methods for measuring conformal coating thickness that are commonly used in the Electronic Manufacturing Services (EMS) and Original Electronic Manufacturer (OEM) industries. A few commonly used methods for checking conformal coating thickness include:...

Publisher: ETS - Energy Technology Systems, Inc.

Testing Printed Circuit Boards for Creep Corrosion in Flowers of Sulfur Chamber

Jul 16, 2015 | Haley Fu; iNEMI, Prabjit Singh, Levi Campbell, Jing Zhang; IBM Corporation, Wallace Ables; Dell Corporation, Dem Lee, Jeffrey Lee; iST-Integrated Service Technology, Jane Li, Solomon Zhang; Lenovo Limited Corporation, Simon Lee; The Dow Chemical Company.

Qualification of electronic hardware from a corrosion resistance standpoint has traditionally relied on stressing the hardware in a variety of environments. Before the development of tests based on mixed flowing gas (MFG), hardware was typically exposed to temperature-humidity cycling. In the pre-1980s era, component feature sizes were relatively large. Corrosion, while it did occur, did not in general degrade reliability. There were rare instances of the data center environments releasing corrosive gases and corroding hardware. One that got a lot of publicity was the corrosion by sulfur-bearing gases given off by data center carpeting. More often, corrosion was due to corrosive flux residues left on as-manufactured printed circuit boards (PCBs) that led to ion migration induced electrical shorting. Ion migration induced failures also occurred inside the PCBs due to poor laminate quality and moisture trapped in the laminate layers....

Publisher: iNEMI (International Electronics Manufacturing Initiative)

What is Kelvin Test?

Jul 14, 2015 | Rick Meraw, Todd Kolmodin, Manfred Ludwig, Holger Kern.

The PCB industry is ever changing and adapting to new technologies. OEM specifications and requirements have also advanced due to these technologies. In some cases the OEMs are asking for a low resistance test to be performed on some or all electrical test nets of the PCB or on the holes of the PCB. This requirement is typically not well defined on the fabrication drawing and that leads to misleading conclusions by the fabrication house (...)

This paper will use the data gathered by the company’s operations to outline what a 4-wire Kelvin test is and how it can be used. Several examples will be illustrated of what the 4 wire Kelvin test can and cannot do. A clear definition of what limitations are present during the testing operation will be defined. The paper will assist designers in understanding how the low resistance test can assist them and also identify causes that can identify unwanted concerns/issues....

Publisher: Gardien Services USA

Reliability Study of Bottom Terminated Components

Jul 14, 2015 | Jennifer Nguyen, Hector Marin, David Geiger, Anwar Mohammed, and Murad Kurwa

Bottom terminated components (BTC) are leadless components where terminations are protectively plated on the underside of the package. They are all slightly different and have different names, such as QFN (quad flat no lead), DFN (dual flat no lead), LGA (land grid array) and MLF (micro lead-frame. BTC assembly has increased rapidly in recent years. This type of package is attractive due to its low cost and good performance like improved signal speeds and enhanced thermal performance.

However, bottom terminated components do not have any leads to absorb the stress and strain on the solder joints. It relies on the correct amount of solder deposited during the assembly process for having a good solder joint quality and reliable reliability. Voiding is typically seen on the BTC solder joint, especially on the thermal pad of the component. Voiding creates a major concern on BTC component’s solder joint reliability. There is no current industry standard on the voiding criteria for bottom terminated component. The impact of voiding on solder joint reliability and the impact of voiding on the heat transfer characteristics at BTC component are not well understood. This paper will present some data to address these concerns....

Publisher: Flex (Flextronics International)

Predicting Fatigue of Solder Joints Subjected to High Number of Power Cycles

Jul 09, 2015 | Craig Hillman, Nathan Blattau, Matt Lacy

Solder joint reliability of SMT components connected to printed circuit boards is well documented. However, much of the testing and data is related to high-strain energy thermal cycling experiments relevant to product qualification testing (i.e., -55C to 125C). Relatively little information is available on low-strain, high-cycle fatigue behavior of solder joints, even though this is increasingly common in a number of applications due to energy savings sleep mode, high variation in bandwidth usage and computational requirements, and normal operational profiles in a number of power supply applications.

In this paper, 2512 chip resistors were subjected to a high (>50,000) number of short duration (<10 min) power cycles. Environmental conditions and relevant material properties were documented and the information was inputted into a number of published solder joint fatigue models. The requirements of each model, its approach (crack growth or damage accumulation) and its relevance to high cycle fatigue are discussed....

Publisher: DfR Solutions (acquired by ANSYS Inc)

Reliability Screening of Lower Melting Point Pb-Free Alloys Containing Bi

Jul 01, 2015 | Joseph M. Juarez, Michael Robinson, Joel Heebink; Honeywell, Polina Snugovsky, Eva Kosiba, Jeffrey Kennedy, Zohreh Bagheri, Subramaniam Suthakaran, Marianne Romansky; Celestica.

Aerospace and military companies continue to exercise RoHS exemptions and to intensively research the long term attachment reliability of RoHS compliant solders. Their products require higher vibration, drop/shock performance, and combined-environment reliability than the conventional SAC305 alloy provides. The NASA-DoD Lead-Free Electronics Project confirmed that pad cratering is one of the dominant failure modes that occur in various board level reliability tests, especially under dynamic loading.

One possible route to improvement of the mechanical and thermo-mechanical properties of solder joints is the use of Pb-free solders with lower process temperatures. Lower temperatures help reduce the possibility of damaging the boards and components, and also may allow for the use of lower Tg board materials which are less prone to pad cratering defects. There are several Sn-Ag-Bi and Sn-Ag-Cu-Bi alloys which melt about 10°C lower than SAC305. The bismuth in these solder compositions not only reduces the melting temperature, but also improves thermo-mechanical behavior. An additional benefit of using Bi-containing solder alloys is the possibility to reduce the propensity to whisker growth...

Publisher: Honeywell International

Return on Investment of a Pre-Reflow AOI System

Jun 30, 2015 | CyberOptics Corporation

This paper describes the losses from defects at the placement process in the SMT line. Two case studies of European and Taiwanese SMT manufacturers illustrate the actual losses from their defects. An evaluation method to select a pre-reflow AOI system maximizing the return on investment (ROI) is introduced. In the end, ROIs of three commercial pre-reflow AOI systems are compared to demonstrate the importance of selecting an appropriate AOI system. This paper will increase the probability that anyone installing an AOI system during the pre-reflow process will obtain a successful gain with short payback period....

Publisher: CyberOptics Corporation

Automated Fluid Dispensing for Epoxy

Jun 30, 2015 | Eric Sari

Robotics for automated fluid dispensing have the ability to apply a variety of materials including epoxy, silicone, and acrylic coatings. These materials are extensively used in today’s high-speed fluid dispensers for the electronics industry.

Whether a dispenser is applying epoxy or another material, the central concept for applying any form of material remains the same. Specific points of an item being dispensed onto are programmed into the dispensing system. The automated fluid dispensers software interprets the programmed information and keeps the travel path in memory. A robotic arm moves fluid dispensing nozzles along this travel path and applies epoxy onto the surface of the item with precise accuracy. Machine speed can be adjusted to emit varying amounts of epoxy. The overall application process is auto-regulating and will not be disrupted....

Publisher: ETS - Energy Technology Systems, Inc.

Reduce labor by automating your Selective Conformal Coating process

Jun 22, 2015 | Brian Stumm, Wes Noble

Applying conformal coatings to electronics has come a long way since the days of manually coating circuit boards. The extreme accuracy and highly repetitive process of automated conformal coatings is moving the electronics industry towards a more defect-free era for conformal coating. It enables new forms of electronics to become better protected, making it possible for electronics to withstand harsher environments than ever before. The following article is meant to aid in clarifying the advantages of specialty coating systems over manual applications for selective conformal coating. ...

Publisher: ETS - Energy Technology Systems, Inc.

PCB Surface Finishes: A General Review

Jun 22, 2015 | Jun Nable, Ph.D., MacDermid Inc. Waterbury, CT

Surface finishing is an integral part of any PCB fabrication. It is generally applied to exposed Cu connectors and conductors on the board. Surface finishing has numerous important functions. It serves as a protective layer for the Cu connectors during storage. The surface finish helps minimize or reduce tarnish of the Cu substrate. Additionally, since it is the layer that comes into contact with other components during assembly, it ensures good solderability between the PCB and the component during assembly. Furthermore after assembly, the finish helps prolong the integrity of the solder joint during use.

A general review of common PCB surface finishes is presented. The advantages and disadvantages of each are discussed and compared. ...

Publisher: MacDermid Inc.