Printed Circuit Board Assembly & PCB Design Forum

SMT electronics assembly manufacturing forum.

SMTnet
»
Electronics Forum
»
PCB Delamination

PCB Delamination

Subscribe to Thread

Views: 11035

I have encountered PCB delam issue with high density PCB. PC... - May 31, 2012 by Jack

If you think the root cause is excess moisture in the pcb th... - Jun 01, 2012 by Graham

could be down to board design also - are you seeing the dela... - Jun 01, 2012 by aj

Post-reflow delamination is almost always caused by entrappe... - Jun 01, 2012 by davef

You also need to get with the PCB manufacturer. Their is a l... - Jun 01, 2012 by KaHrpr

HI Guys, i am facing similar issues with this BT resin mater... - Jun 01, 2012 by bwjm

Sounds like the boards were not properly manufactured since ... - Jun 04, 2012 by aci

bwjm: Delamination can be attributed to several factors: * ... - Jun 04, 2012 by davef

There is sympthom that the delam only happen on area that ne... - Jun 04, 2012 by Jack

It's called pink ring. ... - Jun 05, 2012 by aci

Definition: Pink Ring - A condition that can exist in multi... - Jun 05, 2012 by aci

Okay, i got the concept. What are advantages of using pink r... - Apr 04, 2013 by susanc

PCB Delamination | 31 May, 2012

I have encountered PCB delam issue with high density PCB. PCB has 42 layers , 5 mm thickness ,laminate material is NelcoN4000-13EP,Tg 210C and Td 350C. Have pre-bake at 125 c for 12 hrs before assy.My reflow temp is standard with 243 peak and TAL is around 85s with possitive ramp at 1.7 c/s. Any advice are welcome..

PCB Delamination | 1 June, 2012

If you think the root cause is excess moisture in the pcb then try to bake it for longer. Even longer then the manufacturers recommendation. It takes a long time for excess moisture to come out of a pcb. Try 24 hours , then 36 hours and see if there is a difference.

PCB Delamination | 1 June, 2012

could be down to board design also - are you seeing the delam in the same area all the time?

PCB Delamination | 1 June, 2012

Post-reflow delamination is almost always caused by entrapped moisture. Here's more from the fine SMTnet Archives ... http://www.smtnet.com/Forums/Index.cfm?CFApp=1&Message_ID=64774

As Graham Cooper suggests in an earlier posting on this thread, baking boards to remove moisture takes a lot more energy than you'd think. Following on with this, Chris Hunt from NPL gave a presentation at IPC APEX 2012 about the results of his research ["Impedance Testing for Sensitivity to Delamination in Printed Circuit Boards" C.P. Hunt, M Wickham, O Thomas, L Zou, MAT 40, March 2010] on baking boards. It was: * Startling how long to took to bake boards * Amazing how ground planes affected the movement and concentration of moisture from the board during baking

PCB Delamination | 1 June, 2012

You also need to get with the PCB manufacturer. Their is a lot that can go wrong with that many layers. If the manufacture is trapping that much moisture. you may have a hard time baking it out. Dave and Graham are right about the time and energy. It takes a long time for moisture to migrate out of the board. If it is trapped by large power and ground planes it may not bake out. Water does not pass through copper.

PCB Delamination | 1 June, 2012

HI Guys, i am facing similar issues with this BT resin material too. PCB specs are 4 layers, Nelco400013, same Tg and Td. My PCB delam after reflow.

The PCB has both side mounted with SMDs. Initial mounting on the btm side after reflow, no delam. But after mounting topside, pass through the reflow and the PCB delam. LF process and max temp is 243 Degree C. Other than baking the PCB, is there other possible reason? Thanks!

PCB Delamination | 4 June, 2012

Sounds like the boards were not properly manufactured since you have baked them prior to assembly. We just had a customer return from China becasue of this issue. We have made 10K without issue. Let me take a stab and ask if they were made in the USA? If not try this: www.americancircuits.com

PCB Delamination | 4 June, 2012

bwjm: Delamination can be attributed to several factors: * Entrapped moisture, processing solutions, and what not that expands when heated to normal soldering temperature * Excessive soldering temperature * Excessive laminating temperature * Defective laminate material * Problem in oxide treatment of innerlayer * Contamination at the laminate interface

PCB Delamination | 4 June, 2012

There is sympthom that the delam only happen on area that near to via location.What does this try to relate to? It appears on both primary and secondary side even pass through with primary reflow process only.

PCB Delamination | 5 June, 2012

It's called pink ring.

PCB Delamination | 5 June, 2012

Definition: Pink Ring - A condition that can exist in multilayer printed circuit or wiring boards, in which the oxide around a through-hole inner layer interface is chemically removed, and there is a lack of adhesion of the inner layer to the dielectric substrate.

www.americancircuits.com

PCB Delamination | 4 April, 2013

Okay, i got the concept. What are advantages of using pink ring? http://www.ccsintlcircuits.com/flexiblepcb.html

SMTnet
»
Electronics Forum
»
PCB Delamination

Nozzles, Feeders, Spare Parts - Siemens, Fuji, Juki, Yamaha, etc...

World's Best Reflow Oven Customizable for Unique Applications

Reflow Soldering 101 Training Course

© 1995-2024 SMTnet

See Your 2024 IPC Certification Training Schedule for Eptac

Now Online

76
Visitors

3
Members

Who are SMTnet visitors?

Become a member now and receive the value and benefits of membership.

Thermal Interface Material Dispensing

convection smt reflow ovens

Get your business noticed