Industry News | 2012-05-30 18:23:07.0
IPC Midwest Conference & Exhibition™ will highlight advances in assembly materials, assembly processes and reliability testing to help electronics companies address critical challenges in manufacturing defect-free, quality electronics
Industry News | 2013-02-19 18:26:34.0
In recognition of their extraordinary contributions to IPC and the electronic interconnect industry, Ray Prasad, Ray Prasad Consultancy Group and Lionel Fullwood, WKK Distribution Ltd., were honored with the IPC Raymond E. Pritchard Hall of Fame Award.
Industry News | 2023-07-19 10:18:06.0
IPC China Skills Competition has been upgraded to IPC Masters Competition China 2023. The competition was co-organized with Pudong New Area Association for Quality and Technology Shanghai and held July 11-13 in Shanghai.
Industry News | 2024-02-05 14:05:05.0
The SMTA is pleased to announce the Best Papers from SMTA International 2023. The winners were selected by members of the conference technical committee. This year awards were given for the "Best of Proceedings" category but also for a new designation of "Best Practical and Applications-Based Knowledge." A plaque is given to primary authors of all winning papers for these exceptional achievements.
Industry News | 2011-04-20 21:26:17.0
IPC — Association Connecting Electronics Industries® presented Special Recognition, Distinguished Committee Leadership and Committee Service awards and a Presidents Award at IPC APEX EXPO™, held April 10–14, in Las Vegas.
New Equipment | Cable & Wire Harness Equipment
Low Cost Table Top Crimp Machine. The C 200 is a table top low cost crimp tool which takes a variety of dies from different manufacturers. Air operated using standard factory air (5 bar min), with a pressing capacity of up to 1,200 kp, this portable
New Equipment | Solder Paste Stencils
Simplify and Speed Up QFN and LGA device rework. StencilMate™ leadless device rework stencils make the process of reworking leadless devices such as QFNs and LGAs simple and fast. These adhesive-backed poyimide stencils are placed on to the bottom o
Teresa Rowe, IPC director of assembly standards, highlights several revisions to IPC J-STD-001F, Requirements for Soldered Electrical and Electronic Assemblies and IPC-A-610F, Acceptability of Electronic Assemblies. The documents have been updated to
Technical Library | 2020-12-29 20:55:46.0
Voiding in solder joints has been studied extensively, and the effects of many variables compared and contrasted with respect to voiding performance. Solder paste flux, solder powder size, stencil design, circuit board design, via-in-pad design, surface finish, component size, reflow profile, vacuum reflow, nitrogen reflow and other parameters have been varied and voiding quantified for each. The results show some differences in voiding performance with respect to most of these variables but these variables are not independent of each other. Voiding in solder joints is a complex issue that often requires multiple approaches to reduce voiding below required limits. This paper focuses on solutions to voiding for commonly used bottom terminated components (BTCs).
Technical Library | 2015-07-14 13:19:10.0
Bottom terminated components (BTC) are leadless components where terminations are protectively plated on the underside of the package. They are all slightly different and have different names, such as QFN (quad flat no lead), DFN (dual flat no lead), LGA (land grid array) and MLF (micro lead-frame. BTC assembly has increased rapidly in recent years. This type of package is attractive due to its low cost and good performance like improved signal speeds and enhanced thermal performance. However, bottom terminated components do not have any leads to absorb the stress and strain on the solder joints. It relies on the correct amount of solder deposited during the assembly process for having a good solder joint quality and reliable reliability. Voiding is typically seen on the BTC solder joint, especially on the thermal pad of the component. Voiding creates a major concern on BTC component’s solder joint reliability. There is no current industry standard on the voiding criteria for bottom terminated component. The impact of voiding on solder joint reliability and the impact of voiding on the heat transfer characteristics at BTC component are not well understood. This paper will present some data to address these concerns.
