Industry News | 2019-04-03 20:07:41.0
Practical Components is a leading international distributor of mechanical IC samples or “dummy” components that has added a new SMTA Solder Paste Test Vehicle for Miniaturized Surface Mount Technology (SMT) to its array of Dummy Components, Solder Training Kits and PCB Evaluation Kits.
Technical Library | 2021-04-08 00:30:49.0
As the electronic industry moves to lead-free assembly and finer-pitch circuits, widely used printed wiring board (PWB) finish, SnPb HASL, has been replaced with lead-free and coplanar PWB finishes such as OSP, ImAg, ENIG, and ImSn. While SnPb HASL offers excellent corrosion protection of the underlying copper due to its thick coating and inherent corrosion resistance, the lead-free board finishes provide reduced corrosion protection to the underlying copper due to their very thin coating. For ImAg, the coating material itself can also corrode in more aggressive environments. This is an issue for products deployed in environments with high levels of sulfur containing pollutants encountered in the current global market. In those corrosive environments, creep corrosion has been observed and led to product failures in very short service life (1-5 years). Creep corrosion failures within one year of product deployment have also been reported. This has prompted an industry-wide effort to understand creep corrosion
Industry News | 2021-01-21 08:09:52.0
Indium Corporation announces that it is now offering CW-232,a uniquely formulated flux-cored wire that combines superior wetting speed and spread with extremely low-spatter performance.
Industry News | 2021-02-25 13:23:32.0
Indium Corporation will feature its uniquely formulated flux-cored wire during the virtual IPC APEX Expo, to be held March 8-12.
Technical Library | 2020-10-27 02:07:31.0
For companies that choose to take the Pb-free exemption under the European Union's RoHS Directive and continue to manufacture tin-lead (Sn-Pb) electronic products, there is a growing concern about the lack of Sn-Pb ball grid array (BGA) components. Many companies are compelled to use the Pb-free Sn-Ag-Cu (SAC) BGA components in a Sn-Pb process, for which the assembly process and solder joint reliability have not yet been fully characterized. A careful experimental investigation was undertaken to evaluate the reliability of solder joints of SAC BGA components formed using Sn-Pb solder paste. This evaluation specifically looked at the impact of package size, solder ball volume, printed circuit board (PCB) surface finish, time above liquidus and peak temperature on reliability. Four different BGA package sizes (ranging from 8 to 45 mm2) were selected with ball-to-ball pitch size ranging from 0.5mm to 1.27mm. Two different PCB finishes were used: electroless nickel immersion gold (ENIG) and organic solderability preservative (OSP) on copper. Four different profiles were developed with the maximum peak temperatures of 210oC and 215oC and time above liquidus ranging from 60 to 120 seconds using Sn-Pb paste. One profile was generated for a lead-free control. A total of 60 boards were assembled. Some of the boards were subjected to an as assembled analysis while others were subjected to an accelerated thermal cycling (ATC) test in the temperature range of -40oC to 125oC for a maximum of 3500 cycles in accordance with IPC 9701A standard. Weibull plots were created and failure analysis performed. Analysis of as-assembled solder joints revealed that for a time above liquidus of 120 seconds and below, the degree of mixing between the BGA SAC ball alloy and the Sn-Pb solder paste was less than 100 percent for packages with a ball pitch of 0.8mm or greater. Depending on package size, the peak reflow temperature was observed to have a significant impact on the solder joint microstructural homogeneity. The influence of reflow process parameters on solder joint reliability was clearly manifested in the Weibull plots. This paper provides a discussion of the impact of various profiles' characteristics on the extent of mixing between SAC and Sn-Pb solder alloys and the associated thermal cyclic fatigue performance.
Technical Library | 2014-08-07 15:13:44.0
Gold embrittlement in SnPb solder is a well-known failure mechanism in electronic assembly. To avoid this issue, prior studies have indicated a maximum gold content of three weight percent. This study attempts to provide similar guidance for Pb-free (SAC305) solder. Standard surface mount devices were assembled with SnPb and SAC305 solder onto printed boards with various thicknesses of gold plating. The gold plating included electroless nickel immersion gold (ENIG) and electrolytic gold of 15, 25, 35, and 50 microinches over nickel. These gold thicknesses resulted in weight percentages between 0.4 to 7.0 weight percent.
Industry News | 2004-02-04 16:52:03.0
Prepare for the 2006 European Deadline
Electronics Forum | Mon Jul 12 05:54:34 EDT 2010 | xps
Hi everyone, someone knows the correct parameters for reflow the smt devices using SnPb on ENIG finishing ? Someone suggest to use more temperature than others finishing, cause nickel barrier. Someone can confirm this ? There are handbooks or articl
Electronics Forum | Tue Mar 15 17:58:56 EST 2005 | darby
Mat, Are you sure you should be using SnPb HASL boards if you are doing prep for lead free? If you aren't actually going to comply with RoHS then fire away. Nearly all of our assemblies are now ENIG and as any re-design comes up on a HASL board it is
Electronics Forum | Thu Apr 18 16:52:15 EDT 2002 | davef
General comments are: * First place I would look is the supplier of the pins that you are trying to install. Most suppliers that sell press fit components have done a good deal of work to qualify the component and will have all the specifications yo
