New Equipment | Solder Materials
KappTecZ is a high temperature, high strength solder that may be used on most metals, but works extremely well on aluminum, copper and stainless steel. It has a high tolerance to vibration and stress, and good elongation for use on dissimilar metals.
Hand push pcb cutting machine depaneling 330mm length pcba YSV-2M Specification for pcbcuting machine : 1.Easy operating modes 2.Easy setting, edge guiding 3.Cutters re-grinded 4.Avoid micro-cracks v-cut PCB depaneling
Electronics Forum | Wed Jul 03 03:02:35 EDT 2013 | autoel
How to test the reflow solder joint shear strength? What are the specification to test solder joint shear strength? What are the different methods to test the solder joint shear strength? Vijayashree
Electronics Forum | Wed Jul 03 15:40:17 EDT 2013 | davef
Shear tests are [in my opinion] senseless. The shear stress you measure depends more on the shear rate and on the point where the force is applied than on the grain structure. When shearing a component, you not only apply shear stress, but also roll
Industry News | 2022-11-11 07:33:41.0
Lyra Reflow Oven is a soft soldering that realizes the mechanical and electrical connection between the solder ends of surface mount components or the pins and the printed board pads by remelting the solder paste pre-distributed on the printed board pads.
Industry News | 2003-08-27 10:58:00.0
Lead free solders and embedded passives headline professional development schedule at the 2003 IPC Annual Meeting
Technical Library | 2023-01-17 17:27:13.0
Reflow profile has significant impact on solder joint performance because it influences wetting and microstructure of the solder joint. The degree of wetting, the microstructure (in particular the intermetallic layer), and the inherent strength of the solder all factor into the reliability of the solder joint. This paper presents experimental results on the effect of reflow profile on both 63%Sn 37%Pb (SnPb) and 96.5%Sn 3.0%Ag 0.5%Cu (SAC 305) solder joint shear force. Specifically, the effect of the reflow peak temperature and time above solder liquidus temperature are studied. Nine reflow profiles for SAC 305 and nine reflow profiles for SnPb have been developed with three levels of peak temperature (230 o C, 240 o C, and 250 o C for SAC 305; and 195 o C, 205 o C, and 215 o C for SnPb) and three levels of time above solder liquidus temperature (30 sec., 60 sec., and 90 sec.). The shear force data of four different sizes of chip resistors (1206, 0805, 0603, and 0402) are compared across the different profiles. The shear force of the resistors is measured at time 0 (right after assembly). The fracture surfaces have been studied using a scanning electron microscopy (SEM) with energy dispersive spectroscopy (EDS)
Technical Library | 2007-03-08 19:31:10.0
Reflow profile has significant impact on solder joint performance because it influences wetting and microstructure of the solder joint. The degree of wetting, the microstructure (in particular the intermetallic layer), and the inherent strength of the solder all factor into the reliability of the solder joint. This paper presents experimental results on the effect of reflow profile on both 63%Sn 37%Pb (SnPb) and 96.5%Sn 3.0%Ag 0.5%Cu (SAC 305) solder joint shear force.
Lyra Reflow Oven is a soft soldering that realizes the mechanical and electrical connection between the solder ends of surface mount components or the pins and the printed board pads by remelting the solder paste pre-distributed on the printed board
This animation shows the overview of programming and running of a MYDATA MY500 Jet Printing machine. Check the ''Jet Printing in detail'' video to see how Jet Printing works
SMTnet Express July 11, 2013, Subscribers: 26149, Members: Companies: 13418, Users: 34911 Effect of BGA Reballing and its Influence on Ball Shear Strength by S. Manian Ramkumar Ph.D., Andrew J. Daya, Daniel B. Lewanda; Rochester Institute
Strength of Lead-free BGA Spheres in High Speed Loading Strength of Lead-free BGA Spheres in High Speed Loading Concern about the failure of lead-free BGA packages when portable devices such as cell phones are accidentally dropped and a general
ASYMTEK Products | Nordson Electronics Solutions | https://www.nordson.com/en/divisions/dage/test-types/ball-shear-solder-ball-shear?con=t&page=6
. Products Content Your results for: Ball Shear/Solder Ball Shear Stud pull Nordson DAGE The stud-pull test measures the bond strength of dies and other flat components to the substrate
| https://www.eptac.com/soldertips/defining-shear-forces-for-surface-mounted-components/
., so it is very difficult to define what the shear strength of a solder joint should be. What most people do is find a joint that has worked over time and make comparisons to it based upon a DOE
