New Advanced Precision Auger Pump - Single Pump Solution The Precision Auger pump is designed to work with mid-to-high viscosity liquid such as glues, conductive, and non-conductive adhesive and pastes. The pump is controlled with a servo motor equ
For flip chip attachment of RFID and smartcard IC’s Zymet's NCP’s are designed for flip chip attachment of gold bumped IC’s. Although they are specifically designed for RFID and smartcard assembly they can also be used for other flip chip applicati
Electronics Forum | Thu May 11 11:25:56 EDT 2017 | davef
Key to Rosin Fluxes [from SUPERIOR FLUX & MFG. CO.] Type R (Rosin): Non-activated rosin flux for soldering copper. Residues are non-corrosive and non-conductive. Type RMA (Rosin Mildly Activated): Mildly activated rosin flux that contains no chlori
Electronics Forum | Wed Oct 10 13:59:49 EDT 2007 | petep
I have always understood that on boards (or circuits) operating over 900 MHz, No Clean fluxes are to be avoided. Apparently the residues left behind, while non-conductive and non-corrosive, will change impedence of the circuit. It may be a possibil
Industry News | 2016-02-27 22:11:00.0
GPD Global has advanced its auger pump technology with the introduction of the newly developed Precision Auger Pump. This pump was designed to offer a wide range of functionality in your process development by being compatible with a wide range of auger/cartridge assemblies.
Industry News | 2014-01-29 14:32:03.0
Engineered Material Systems (EMS) debuts its 585-1 Non-Conductive Paste (NCP) designed for flip chip packaging applications.
Technical Library | 2015-12-02 18:32:50.0
(Thermal Compression with Non-Conductive Paste Underfill) Method.The companies writing this paper have jointly developed Copper (Cu) Pillar micro-bump and TCNCP(Thermal Compression with Non-Conductive Paste) technology over the last two+ years. The Cu Pillar micro-bump and TCNCP is one of the platform technologies, which is essentially required for 2.5D/3D chip stacking as well as cost effective SFF (small form factor) package enablement.Although the baseline packaging process methodology for a normal pad pitch (i.e. inline 50μm) within smaller chip size (i.e. 100 mm2) has been established and are in use for HVM production, there are several challenges to be addressed for further development for commercialization of finer bump pitch with larger die (i.e. ≤50μm tri-tier bond pad with the die larger than 400mm2).This paper will address the key challenges of each field, such as the Cu trace design on a substrate for robust micro-joint reliability, TCNCP technology, and substrate technology (i.e. structure, surface finish). Technical recommendations based on the lessons learned from a series of process experimentation will be provided, as well. Finally, this technology has been used for the successful launching of the company FPGA products with SFF packaging technology.
Technical Library | 2020-07-29 19:58:48.0
The majority of flexible circuits are made by patterning copper metal that is laminated to a flexible substrate, which is usually polyimide film of varying thickness. An increasingly popular method to meet the need for lower cost circuitry is the use of aluminum on Polyester (Al-PET) substrates. This material is gaining popularity and has found wide use in RFID tags, low cost LED lighting and other single-layer circuits. However, both aluminum and PET have their own constraints and require special processing to make finished circuits. Aluminum is not easy to solder components to at low temperatures and PET cannot withstand high temperatures. Soldering to these materials requires either an additional surface treatment or the use of conductive epoxy to attach components. Surface treatment of aluminum includes the likes of Electroless Nickel Immersion Gold plating (ENIG), which is extensive wet-chemistry and cost-prohibitive for mass adoption. Conductive adhesives, including Anisotropic Conductive Paste (ACP), are another alternate to soldering components. These result in component substrate interfaces that are inferior to conventional solders in terms of performance and reliability. An advanced surface treatment technology will be presented that addresses all these constraints. Once applied on Aluminum surfaces using conventional printing techniques such as screen, stencil, etc., it is cured thermally in a convection oven at low temperatures. This surface treatment is non-conductive. To attach a component, a solder bump on the component or solder printed on the treated pad is needed before placing the component. The Aluminum circuit will pass through a reflow oven, as is commonly done in PCB manufacturing. This allows for the formation of a true metal to metal bond between the solder and the aluminum on the pads. This process paves the way for large scale, low cost manufacturing of Al-PET circuits. We will also discuss details of the process used to make functional aluminum circuits, study the resultant solder-aluminum bond, shear results and SEM/ EDS analysis.
New Advanced Precision Auger Pump - Single Pump Solution The Precision Auger pump is designed to work with mid-to-high viscosity liquid such as glues, conductive, and non-conductive adhesive and pastes. The pump is controlled with a servo motor equ
Career Center | Rochester, New York USA | Engineering
I have done my undergraduate studies in Mechanical Engineering. I am pursuing my Master's Program in Electronics Packaging. I am currently working as a Research Assistant for RIT-CEMA (Center for Electronics Manufacturing and Assembly). My research
ASYMTEK Products | Nordson Electronics Solutions | https://www.nordson.com/en/divisions/asymtek/fluid-types/conductive-adhesive?page=2
) Materials Thermal Interface Material (TIM) Solder Paste Conformal Coating Materials Adhesives Conductive Adhesive Encapsulant Epoxy Flux Lubricant Primer Reagent Silicone Glue Silver Epoxy Surface Mount Adhesive (SMA
PCB Libraries, Inc. | https://www.pcblibraries.com/Forum/paste-stencil-mask-cadstar_topic1642_post6717.html
) unless setting it to a non-0 width. 2. the pad covers the pattern on Paste Mask layer (it needs to be reassigned to 0 size on Paste Mask layer
