Industry Directory | Consultant / Service Provider / Manufacturer / Other
Taiwan Dry Tech Corp. manufacturer of Eureka Dry Tech Fast Super Dryers for moisture/humidity proof protective storage of PCB, MSD, IC packages, meets IPC/JEDEC J-STD-033 & IPC-1601.
Industry Directory | Consultant / Service Provider / Manufacturer
Eureka Dry Tech's IPC/JEDEC J-Std-033c Ultra Low Humidity Dry Cabinets provides moisture/humidity controlled storage of MSD，PCB, IC packages. Drying technology trusted by millions in replacing baking, nitrogen & desiccant packs.
New Equipment | Solder Materials
I.C.T | Antioxidant Silver Soldering Tin Lead Free Solder Bar for Solder Wave ❙ Introduction I.C.T has been working with suppliers to develop environmentally friendly lead-free solders and related materials and can now supply products that delive
New Equipment | Rework & Repair Equipment
BEST HeatShield Gel™ is a thermal shield water-based gel designed to be used in the PCB rework/repair or board assembly areas in order to provide thermal protection of electronic components. It is truly a revolutionary means to protect components. It
Electronics Forum | Fri Sep 28 07:42:07 EDT 2007 | zanolli
We have the need to verify that proper intermetallic layer between a 100% Sn plated contact and the solder joint is being formed. Never having done this before: Is there any specifications, etc. that we can use as acceptability criteria?
Electronics Forum | Fri Sep 28 16:49:48 EDT 2007 | davef
good * No IMC => bad Intermetallic growths are diffusion limited, and therefore the thickness of the intermetallic is given by: z^2 = (Do)(t)exp[-Q/RT] Where Do (m^2 s-1) is the diffusion coefficient, T(�K) is the temperature, Q (J mol-1) is the act
Industry News | 2018-04-09 19:48:04.0
SMTA Europe announces Session 1 Technical Program on Predicting Component Life at the “Electronics in Harsh Environments Conference” to be held in Amsterdam, Netherlands, on April 25th, 2018.
Industry News | 2012-02-07 16:20:22.0
Nihon Superior announces that its Senior Technical Advisor Keith Sweatman will present the paper titled “Effect of Cooling Rate on the Intermetallic Layer in Solder Joints” at the upcoming IPC APEX Expo.
Technical Library | 2023-01-17 17:27:13.0
Reflow profile has significant impact on solder joint performance because it influences wetting and microstructure of the solder joint. The degree of wetting, the microstructure (in particular the intermetallic layer), and the inherent strength of the solder all factor into the reliability of the solder joint. This paper presents experimental results on the effect of reflow profile on both 63%Sn 37%Pb (SnPb) and 96.5%Sn 3.0%Ag 0.5%Cu (SAC 305) solder joint shear force. Specifically, the effect of the reflow peak temperature and time above solder liquidus temperature are studied. Nine reflow profiles for SAC 305 and nine reflow profiles for SnPb have been developed with three levels of peak temperature (230 o C, 240 o C, and 250 o C for SAC 305; and 195 o C, 205 o C, and 215 o C for SnPb) and three levels of time above solder liquidus temperature (30 sec., 60 sec., and 90 sec.). The shear force data of four different sizes of chip resistors (1206, 0805, 0603, and 0402) are compared across the different profiles. The shear force of the resistors is measured at time 0 (right after assembly). The fracture surfaces have been studied using a scanning electron microscopy (SEM) with energy dispersive spectroscopy (EDS)
Technical Library | 2007-03-08 19:31:10.0
Reflow profile has significant impact on solder joint performance because it influences wetting and microstructure of the solder joint. The degree of wetting, the microstructure (in particular the intermetallic layer), and the inherent strength of the solder all factor into the reliability of the solder joint. This paper presents experimental results on the effect of reflow profile on both 63%Sn 37%Pb (SnPb) and 96.5%Sn 3.0%Ag 0.5%Cu (SAC 305) solder joint shear force.
SMTnet Express, June 20, 2019, Subscribers: 32,068, Companies: 10,815, Users: 24,854 Dissolution in Service of the Copper Substrate of Solder Joints Credits: Nihon Superior Co., Ltd. It is well known that during service the layer of Cu6Sn5
Effects of reflow profile and thermal conditioning on intermetallic compound thickness for SnAgCu soldered joints. Effects of reflow profile and thermal conditioning on intermetallic compound thickness for SnAgCu soldered joints. The purpose
.gif)
