Industry Directory | Distributor
Suppliers to the PCB Industry with a huge range of products including copper clad laminates, drill boards and consumables.
Industry Directory | Manufacturer
A manufacturer of desoldering braid (wick) with an emphasis on continuing advancement in soldering/desoldering technology, visual and x-ray inspection systems, fume extraction, and solder paste inspection systems.
New Equipment | Assembly Services
G9 + automatic vision printing machine is a new product for SMT high-end application field, which can perfectly meet the process requirements of 03015, 0.25pich and other fine spacing, high precision and high speed. Introduction to standard function
New Equipment | Cleaning Equipment
Fully automatic stencil cleaning system MLPBT-750 Application fields of "MLPBT-750 steel mesh cleaning machine": ●Suitable for cleaning various types of stencils such as steel mesh, copper mesh, microporous mesh, and wafer tray [see the following fi
Electronics Forum | Thu Jun 07 05:11:42 EDT 2012 | cp38260
Hi, I have pcbs (Duroid/RT 5880) with raw copper, soldered in vapour-phase chamber at 230 degrees Celsius. During soldering, copper gets tarnished. Cleaning with Vigon A250 removes the tarnished layer. Indeed, in the VigonA250 techn. datasheet it is
Electronics Forum | Fri Apr 16 11:03:35 EDT 2004 | davef
Your copper corrosion is not good. It indicates that you have not done a good job in cleaning. [We assume this is a medium green color, not unlike the color of the solder mask on your board, that is almost like a translucent lacquer; rather than th
Industry News | 2003-06-10 08:16:44.0
The following text describes the application of NWA Quality Analyst to quality control in the assembly of electronic components.
Industry News | 2009-03-12 18:25:36.0
The SMTA International Technical Committee invites you to submit an abstract for the 2009 conference. Short course descriptions are also being solicited.
Parts & Supplies | Pick and Place/Feeders
KGA-M3801-000 YAMAHA lens cleaner cleaning oil lens oil original authentic KH5-M655A-02X Nozzle Switching Station Optical Fiber FIBER YAMAHA Dedicated Optical Fiber Cable KHJ-MC400-000 KHJ-MC400-002 Electric FEEDER 24MM Electric Feeder SS FEEDER K
Parts & Supplies | Pick and Place/Feeders
KHY-M221A-A0 KGT-M221A-A0 YAMAHA YG12 tank chain gland KHY-M2267-00 YG12 tank chain YS12 towline keel X axis PISCO SP2550 R75 KHY-M2276-S0 YS12 screw X-axis YG12 X-axis screw YG12F YS12F screw guide KHY-M371R-00 RAIL GUIDE 12P YS24 YS100 Feida pl
Technical Library | 2016-09-08 16:27:49.0
In this investigation a test matrix was completed utilizing 900 electrodes (small circuit board with parallel copper traces on FR-4 with LPI soldermask at 6, 10 and 50 mil spacing): 12 ionic contaminants were applied in five concentrations to three different spaced electrodes with five replicas each (three different bare copper trace spacing / five replications of each with five levels of ionic concentration). The investigation was to assess the electrical response under controlled heat and humidity conditions of the known applied contamination to electrodes, using the IPC SIR (surface insulation resistance) J-STD 001 limits and determine at what level of contamination and spacing the ionic / organic residue has a failing effect on SIR.
Technical Library | 2020-08-27 01:22:45.0
Initially adopted internal specifications for acceptance of printed circuit boards (PCBs) used for wire bonding was that there were no nodules or scratches allowed on the wirebond pads when inspected under 20X magnification. The nodules and scratches were not defined by measurable dimensions and were considered to be unacceptable if there was any sign of a visual blemish on wire-bondable features. Analysis of the yield at a PCB manufacturer monitored monthly for over two years indicated that the target yield could not be achieved, and the main reasons for yield loss were due to nodules and scratches on the wirebonding pads. The PCB manufacturer attempted to eliminate nodules and scratches. First, a light-scrubbing step was added after electroless copper plating to remove any co-deposited fine particles that acted as a seed for nodules at the time of copper plating. Then, the electrolytic copper plating tank was emptied, fully cleaned, and filtered to eliminate the possibility of co-deposited particles in the electroplating process. Both actions greatly reduced the density of the nodules but did not fully eliminate them. Even though there was only one nodule on any wire-bonding pad, the board was still considered a reject. To reduce scratches on wirebonding pads, the PCB manufacturer utilized foam trays after routing the boards so that they did not make direct contact with other boards. This action significantly reduced the scratches on wire-bonding pads, even though some isolated scratches still appeared from time to time, which caused the boards to be rejected. Even with these significant improvements, the target yield remained unachievable. Another approach was then taken to consider if wire bonding could be successfully performed over nodules and scratches and if there was a dimensional threshold where wire bonding could be successful. A gold ball bonding process called either stand-off-stitch bonding (SSB) or ball-stitch-on-ball bonding (BSOB) was used to determine the effects of nodules and scratches on wire bonds. The dimension of nodules, including height, and the size of scratches, including width, were measured before wire bonding. Wire bonding was then performed directly on various sizes of nodules and scratches on the bonding pad, and the evaluation of wire bonds was conducted using wire pull tests before and after reliability testing. Based on the results of the wire-bonding evaluation, the internal specification for nodules and scratches for wirebondable PCBs was modified to allow nodules and scratches with a certain height and a width limitation compared to initially adopted internal specifications of no nodules and no scratches. Such an approach resulted in improved yield at the PCB manufacturer.
Nano-copper sintering in formic acid vapor.
Fully automatic stencil cleaning system MLPBT-750 Application fields of "MLPBT-750 steel mesh cleaning machine": ●Suitable for cleaning various types of stencils such as steel mesh, copper mesh, microporous mesh, and wafer tray [see the following fi
Training Courses | | | Other Courses
Other courses related to electronics manufacturing and assembly
Events Calendar | Mon Apr 23 00:00:00 EDT 2018 - Thu Apr 26 00:00:00 EDT 2018 | Shanghai, China
SMTA China East Conference 2018
Career Center | Shen Zhen, China | Management,Sales/Marketing
Working in GLORYPCB for 10 years.knowing electronic supply chain very well. especially for PCB PCBA assembly and other Electronic Manufacturing Service.Glorypcb is a professional electronic manufacturer located in Shenzhen with three facilities.offe
Career Center | kerala, any ware India | Production
i have experience in • Operation of wave soldering and water cleaning machine • Inspection ( Reflow and Post Wave ) • Pre Reflow inspection in SMD • Component forming stuffi
SMTnet Express, May 12, 2022, Subscribers: 25,588, Companies: 11,569, Users: 27,213 Electronics Manufacturing Technical Articles Filling of Microvias and Through Holes by Electrolytic Copper Plating –Current Status and Future
SMTnet Express, November 22, 2017, Subscribers: 31,034, Companies: 10,792, Users: 24,082 Factors Affecting the Adhesion of Thin Film Copper on Polyimide David Ciufo, Hsin-Yi Tsai and Michael J. Carmody; Intrinsiq Materials Inc. The use of copper
ASYMTEK Products | Nordson Electronics Solutions | https://www.nordson.com/en/divisions/march/applications/cleaning?con=t&page=2
Plasma Processing Parameters for Improved Strength of Wire Bonds Nordson MARCH Plasma Cleaning of Copper Leadframe with Ar and Ar/H2 Gases Nordson MARCH Appliance Nordson MARCH First
| https://www.eptac.com/faqs/ask-helena-leo/ask/wet-sponge-cleaning-vs-dry-brass-sponge-cleaning
. Dry Brass Sponge Cleaning Question: Is “wet sponge” solder tip cleaning mandatory for leaded and RoHs soldering? Are there any downfalls to only using the dry “copper sponges”? Question: Is “wet sponge
