Industry Directory | Consultant / Service Provider / Manufacturer
Tropical Stencil is dedicated to providing the highest quality Laser Cut Stencils; with our rapid response, you will have your Stencil delivered on-time.
Industry Directory | Manufacturer
professional manufacturer of pcb
New Equipment | Solder Paste Stencils
These fixture plates facilitate the controlled dipping of flux or paste onto the balls under the BGA packages. Flux or paste is controlled at a depth of 50-60% per cent of the ball diameter prior to placement of a BGA or to place a PoP component on t
New Equipment | Assembly Services
Fine Line Stencil is Committed to Delivering the Highest Quality Laser Stencils in the Industry LPKF Laser Technology / SMT Stencil Laser Technology Laser Slic Stencils / Laser Ultra Slic Stencils Custom Apertures Dog Bone, Home Plate, K
Electronics Forum | Fri Jul 13 14:56:01 EDT 2001 | stevenamacdonald
One of our board vendors recently switched their stencil design to home plate apertures. Since the change the quality and yield of their PCB's has went south, Could this process change be the cause?
Electronics Forum | Mon Jul 16 14:38:22 EDT 2001 | ohboy
If your pad designs don't meet IPC recommendations, using home plate may have adversely affected the (possibly marginal) placement tolerances. This could also be caused by an incorrect home plate design, which IPC has also given recommendations for,
Used SMT Equipment | Screen Printers
Two sets of blades with some poly inserts and a small roll of Ekra wiper paper; 10 support pins; A removable tool plate that can be adjusted by the leveling feet on the bottom. Was usedt to print 150um apertures so I believe it’s better than most use
Industry News | 2011-03-28 13:24:06.0
Eleven products have been selected for inclusion in the Innovative Technology Center at IPC APEX EXPO™, April 12–14, 2011, in Las Vegas, according to show organizer IPC – Association Connecting Electronics Industries. Assessed by a review board of industry experts, the products were selected based on their representation of a new or emerging technology of significant value and relevance to the electronics manufacturing industry.
Industry News | 2012-01-13 13:27:59.0
The SMT stencil market has a slew of new options in foil materials, coatings and cutting technologies, all of which promise to improve the solder paste printing process. Which of these options really do help assemblers keep yields up and costs down, and which don’t?
Technical Library | 2023-08-04 15:27:30.0
A designed experiment evaluated the influence of several variables on appearance and strength of Pb-free solder joints. Components, with leads finished with nickel-palladium-gold (NiPdAu), were used from Texas Instruments (TI) and two other integrated circuit suppliers. Pb-free solder paste used was tin-silver-copper (SnAgCu) alloy. Variables were printed wiring board (PWB) pad size/stencil aperture (the pad finish was consistent; electrolysis Ni/immersion Au), reflow atmosphere, reflow temperature, Pd thickness in the NiPdAu finish, and thermal aging. Height of solder wetting to component lead sides was measured for both ceramic plate and PWB soldering. A third response was solder joint strength; a "lead pull" test determined the maximum force needed to pull the component lead from the PWB. This paper presents a statistical analysis of the designed experiment. Reflow atmosphere and pad size/stencil aperture have the greatest contribution to the height of lead side wetting. Reflow temperature, palladium thickness, and preconditioning had very little impact on side-wetting height. For lead pull, variance in the data was relatively small and the factors tested had little impact.
Technical Library | 2024-04-08 15:46:36.0
A designed experiment evaluated the influence of several variables on appearance and strength of Pb-free solder joints. Components, with leads finished with nickel-palladium-gold (NiPdAu), were used from Texas Instruments (TI) and two other integrated circuit suppliers. Pb-free solder paste used was tin-silver-copper (SnAgCu) alloy. Variables were printed wiring board (PWB) pad size/stencil aperture (the pad finish was consistent; electrolysis Ni/immersion Au), reflow atmosphere, reflow temperature, Pd thickness in the NiPdAu finish, and thermal aging. Height of solder wetting to component lead sides was measured for both ceramic plate and PWB soldering. A third response was solder joint strength; a "lead pull" test determined the maximum force needed to pull the component lead from the PWB. This paper presents a statistical analysis of the designed experiment. Reflow atmosphere and pad size/stencil aperture have the greatest contribution to the height of lead side wetting. Reflow temperature, palladium thickness, and preconditioning had very little impact on side-wetting height. For lead pull, variance in the data was relatively small and the factors tested had little impact.
ASYMTEK Products | Nordson Electronics Solutions | https://www.nordson.com/en/divisions/efd/resource-center/solder-selection-guide
. POWDER SIZE Powder Type Powder Size (micron) Gullwing Lead Pitch (mm / in) Square /Circle Aperture (mm / in) Dispense Dot Dia. (mm/in) General Purpose Tip Gauge Tapered Tip Gauge II 45-75
