Welcome to the next generation in PWB test solutions. We combine an exceptional team of technology and applications experts with HIOKI's industry-leading systems to enhance your reliability and to speed up your product development process.
New Equipment | Rework & Repair Equipment
The Hakko FX-888D is an updated digital version of the popular FX-888 and includes several new features. User selectable preset temperatures and digital calibration simplify user setup and operation, and the new password protection and low temperatur
GenX Series X-ray Inspection Systems The new GenX series x-ray inspection systems come in three model choices corresponding to the power level of their specific x-ray source and can be configured with various detectors to provide a wide range of hi
Electronics Forum | Sun Jan 18 10:13:59 EST 2004 | davef
Materials added to solder can change its appearance. For instance: * Gold in tin/lead solder is dull / grainy * Palladium in tin/lead solder is dull / grainy We do NOT advocate using visual appearance to define the appearance of a good and a bad so
Electronics Forum | Mon Jan 19 14:54:38 EST 2004 | cyber_wolf
How did you come to the conclusion that you are having a cold joint problem. Just by appearance ? As Dave stated if you have any of the metals that he listed in the joints they will appear to be dull and grainy sometimes. But... Dave, I will have t
Industry News | 2009-02-03 13:34:04.0
New PCB Rework, Repair, Fabrication Training & Consulting Services.
Industry News | 2022-11-11 07:33:41.0
Lyra Reflow Oven is a soft soldering that realizes the mechanical and electrical connection between the solder ends of surface mount components or the pins and the printed board pads by remelting the solder paste pre-distributed on the printed board pads.
Technical Library | 2020-12-07 15:26:06.0
Temperature cycling testing is a method of accelerated life testing done to PCCs that are exposed to normal operation temperature variations over its lifetime. During the testing, intermittent "open" failures can first occur at the hot and cold extremes of the test, exposing weaknesses in the design and assembly. A poor/weak solder joint fatigues, a via trace or barrel cracks, loose connections or a component fails all causing an intermittent open. When not at extreme temperatures, the PCC assembly relaxes, the "open" closes creating electrical connectivity. If you are monitoring the PCC under test in-situ you will know that an intermittent failure has occurred, and the test could be stopped for inspection. If in-situ monitoring was not implemented, you would not know if there were intermittent failures or not. The PCC gets powered up and works fine at room temperature.
Technical Library | 2020-12-10 15:49:40.0
Electronic assemblies should have longer and longer service life. Today there are partially demanded 20 years of functional capability for electronics for automotive application. On the other hand, smaller components, such as resistors of size 0201, are able to endure an increasing number of thermal cycles until fail of solder joints, so these are tested sometimes up to 4000 cycles. But testing until the end of life is essential for the determination of failure rates and the prognosis of reliability. Such tests require a lot of time, but this is often not available in developing of new modules. A further acceleration by higher cycle temperatures is usually not possible, because the materials are already operated at the upper limit of the load. However, the duration can be shortened by the use of liquids for passive tests, which allow faster temperature changes and shorter dwell times because of better heat transfer compared to air. The question is whether such tests lead to comparable results and what failure mechanisms are becoming effective. The same goes for active temperature cycles, in which the components itself are heated from inside and the substrate remains comparatively cold. This paper describes the various accelerated temperature cycling tests, compares and evaluates the related degradation of solder joints.
Lyra Reflow Oven is a soft soldering that realizes the mechanical and electrical connection between the solder ends of surface mount components or the pins and the printed board pads by remelting the solder paste pre-distributed on the printed board
Dinghua Technology-- the leading manufacturer of BGA rework station, Automatic screw locking machine, Automatic soldering station and non-standard equipment. For more details, please just contact John, WhatsApp/Wechat:+86 1576811 4827 , Skype: si
Training Courses | | | PCB Rework and Hand Soldering Courses
The PCB rework and hand soldering courses courses cover techniques of rework and repair of PCBs, BGAs and other electronics assemblies, and teach fundamentals of soldering of electronics assemblies.
Events Calendar | Thu Aug 23 00:00:00 EDT 2018 - Thu Aug 23 00:00:00 EDT 2018 | ,
Strain Gauge Data Can Be Misleading | Predicting Strain Levels Caused by Mounting PCBs in Housing Using the ICT Analysis Feature of Sherlock
Heller Industries Inc. | https://hellerindustries.com/wp-content/uploads/2018/07/Vacuum-Void-Reduction-Reflow.pdf
Vacuum Reflow Processing On Solder Joint Voiding To be published in the Proceedings of SMTA International, September 17 - 21, 2016, Rosemont, IL
PCB Libraries, Inc. | https://www.pcblibraries.com/forum/RSS_new-2016-solder-joint-goals_topic1921.xml
PCB Libraries Forum : New 2016 Solder Joint Goals PCB Libraries Forum : New 2016 Solder Joint Goals This is an XML content feed of
