Industry Directory | Consultant / Service Provider / Equipment Dealer / Broker / Auctions / Manufacturer / Manufacturer's Representative
Main Products: 1. Original new and Original Used SMT/AI Spare Parts. 2. SMT Equipments And Related Machine( Loader/Unloader,SMT Calibration, SMT Feeder Carts,Conveyer etc.) 3. Maintenace and Repair Service
Industry Directory | Manufacturer
BLIND RIVETS,BLIND NUTS,BLIND RIVETING TOOLS,STAINLESS STEEL CABLE TIES
Proven Peel Back Force Measurement Supplying consistent SMT carrier packaging is critical for customers using SMT pick-and-place machines. Nothing will stop a production line faster than carrier cover tape that doesn’t peel back properly. The proble
.jpg)
High Strength Cutting Unlimit Depanel HRC 60~63 Supplier In China Chuangwei Machine Diagram: Unlimit pcb depaneler supplier in China 1.Cutting any length 2.Easy blade adjusting 3.Protecting PCB board 4.Safety protecting hand Specification:
Used SMT Equipment | Semiconductor & Solar
Bondtester by DAGE, in good condition. DAGE Series 4000 Bondtester product information. The 4000 bondtester is multipurpose, capable of performing all pull and shear applications. The 4000 bondtester can be configured as a simple bond wire pull
Industry News | 2014-05-22 15:42:29.0
Baja Bid announces their next online auction. This event includes assets from OneChip Photonics in Kanata, Ontario Canada.
Industry News | 2014-06-03 13:04:15.0
The OneChip Photonics facility in Kanata; Ontario, Canada will be closing their site and all assets are being sold via an online auction. The bidding for the auction will open promptly at 4:00am EST on June 3, 2014 with Lots 1-512 beginning to close at 11am EST on June 4, 2014.
Technical Library | 2023-01-17 17:27:13.0
Reflow profile has significant impact on solder joint performance because it influences wetting and microstructure of the solder joint. The degree of wetting, the microstructure (in particular the intermetallic layer), and the inherent strength of the solder all factor into the reliability of the solder joint. This paper presents experimental results on the effect of reflow profile on both 63%Sn 37%Pb (SnPb) and 96.5%Sn 3.0%Ag 0.5%Cu (SAC 305) solder joint shear force. Specifically, the effect of the reflow peak temperature and time above solder liquidus temperature are studied. Nine reflow profiles for SAC 305 and nine reflow profiles for SnPb have been developed with three levels of peak temperature (230 o C, 240 o C, and 250 o C for SAC 305; and 195 o C, 205 o C, and 215 o C for SnPb) and three levels of time above solder liquidus temperature (30 sec., 60 sec., and 90 sec.). The shear force data of four different sizes of chip resistors (1206, 0805, 0603, and 0402) are compared across the different profiles. The shear force of the resistors is measured at time 0 (right after assembly). The fracture surfaces have been studied using a scanning electron microscopy (SEM) with energy dispersive spectroscopy (EDS)
Technical Library | 2021-11-03 17:05:39.0
Additively printed circuits provide advantages in reduced waste, rapid prototyping, and versatile flexible substrate choices relative to conventional circuit printing. Copper (Cu) based inks along with intense pulsed light (IPL) sintering can be used in additive circuit printing. However, IPL sintered Cu typically suffer from poor solderability due to high roughness and porosity. To address this, hybrid Cu ink which consists of Cu precursor/nanoparticle was formulated to seed Cu species and fill voids in the sintered structure. Nickel (Ni) electroplating was utilized to further improve surface solderability. Simulations were performed at various electroplating conditions and Cu cathode surface roughness using the multi-physics finite element method. By utilizing a mask during IPL sintering, conductivity was induced in exposed regions; this was utilized to achieve selective Ni-electroplating. Surface morphology and cross section analysis of the electrodes were observed through scanning electron microscopy and a 3D optical profilometer. Energy dispersive X-ray spectroscopy analysis was conducted to investigate changes in surface compositions. ASTM D3359 adhesion testing was performed to examine the adhesion between the electrode and substrate. Solder-electrode shear tests were investigated with a tensile tester to observe the shear strength between solder and electrodes. By utilizing Cu precursors and novel multifaceted approach of IPL sintering, a robust and solderable Ni electroplated conductive Cu printed electrode was achieved.
Proven Peel Back Force Measurement Supplying consistent SMT carrier packaging is critical for customers using SMT pick-and-place machines. Nothing will stop a production line faster than carrier cover tape that doesn’t peel back properly. The proble
link:https://www.ascen.ltd/Blog/Solutio/493.html ASCEN PCB separator ASC-620 PCB cutting machine can use for cutting LED long board and also can use to the PCBA with the high component separate operation.It is the best way to replace the way to purch
Career Center | Milpitas, California USA | Engineering,Production,Quality Control,Research and Development,Technical Support
Winslow Automation, Inc. (aka Six Sigma), an industry leader in electronic component interconnect technology & related test and failure analysis services, is seeking individuals specializing in materials lab testing to join our team. We have openin
Career Center | Toronto,, Ontario Canada | Engineering,Research and Development
DEBTANU BASU 40 Fountain Head Road Toronto, ON M3J2V1 (416) 514 0619 Cell: 416 258 7488 E-mail: debtanubasu@aol.com With more than six years of experience in the field of flip chip technologies seeking a challenging technical position in the field
Career Center | Sto. Tomas, Batangas, Philippines | Engineering
SKILLS & EXPERIENCES A.Materials engineering and management 1.Handles matters about materials -Ceramic and laminate substrates & Surface Mount Devices (SMDs) i.e. chip capacitors and resistors -Perishable materials i.e. solder paste (including Pb-fr
SMTnet Express July 11, 2013, Subscribers: 26149, Members: Companies: 13418, Users: 34911 Effect of BGA Reballing and its Influence on Ball Shear Strength by S. Manian Ramkumar Ph.D., Andrew J. Daya, Daniel B. Lewanda; Rochester Institute
Strength of Lead-free BGA Spheres in High Speed Loading Strength of Lead-free BGA Spheres in High Speed Loading Concern about the failure of lead-free BGA packages when portable devices such as cell phones are accidentally dropped and a general
GPD Global | https://www.gpd-global.com/co_website/peelforcetester.php
Peel Back Force Tester Home Products Fluid Dispensing Equipment High Precision Dispenser -MAX Series Large Format Board Dispensing -DS Series Table Top Dispensing Equipment Loader
| https://www.eptac.com/soldertips/defining-shear-forces-for-surface-mounted-components/
: The IPC does not have any specification that discusses the strength or shear forces of solder or components mounted onto pads or into plated through holes
