SMT, PCB Electronics Industry News

Seika to Highlight Leading Equipment at SMTAI 2009

Sep 17, 2009

TORRANCE, CA — September 2009 — Seika Machinery, Inc., a leading provider of advanced machinery, materials and engineering services, will highlight Sayaka’s Table-Top Router, Hirox’s 3-D Microscope and the McDry MB-302 Low Temp Baking Cabinet in booth 617 at the upcoming SMTA International exhibition and conference, scheduled to take place October 6-7, 2009 at The Town and Country Resort and Convention Center in San Diego.

Sayaka Routers are the ideal solution for stress-free depanelization, providing a fixture-based highly efficient dust vacuum system. The routers provide clean and precise depanelization for densely populated PCBs, and the advanced image-processing software offers point-and-click operation for programming router paths. Additional features of Sayaka PCB Routers include automatic alignment compensation by CCD camera, user-friendly operation, extended bit life by automatic router bit depth adjustment, improved tact time, and a calibration-free linear robot. The table top models offer offline software programming.

Seika also will feature the McDry MB-302 Low Temp Baking Cabinet. The cabinet conforms to IPC-J-STD 033B specifications, maintaining a baking temperature of

40 degrees C and under 5 percent RH level to bake and recondition moisture-sensitive components. This versatile system also acts as a storage cabinet when not in baking mode.

Finally, HIROX Systems are dedicated digital microscopes, allowing a sample to be observed directly through a lens. The microscopes have been optimized for the characteristics of the imaging sensor — a flat, 2-D array with a known readout rate, response curve, pixel size, etc.

In a conventional microscope, the optics of the eye have to be figured into the design parameters and that requirement may be different from, and potentially conflict with, those that would produce optimal images with an electronic imaging sensor. Because the HIROX microscopes have been designed only for digital imaging, no compromises have been made to accommodate the eye’s optics. However, the systems are, in fact, often able to take advantage of sight physiology and visual signal processing to provide unique observational capabilities, i.e. 3-D rotational microscopy.

The HIROX MX-BGAZ II lens allows ball joints to be observed non-destructively. Additionally, a 3-D optical rotary ring enables 3-D observation. This lens incorporates special hardware, such as a prism tip with lighting and a cushion mechanism to ensure comfortable observation.

Furthermore, observation of the BGA exterior in detail helps specify various problems, such as overheating, oxidation, air foam formation, and their causes. The MX-BGAZ II allows inspection of the BGA ball’s upper and lower joints by changing the observation angle through the optical rotary ring. This information is useful in reviewing the temperature profiles.

For more information about any of these products, visit Seika in booth 617 at the show or visit http://www.seikausa.com.

About Seika Machinery, Inc.

Seika Machinery, Inc. (SMI) is a subsidiary of Seika Corporation, Japan and member of the Mitsubishi Global Group. SMI provides electronics manufacturers with advanced machinery, superior materials and engineering services.

Oct 02, 2017 -

SMTAI Round Table: “High Time to Close the Gender Gap in STEM” Recording Available Now

Sep 18, 2017 -

Seika to Participate in SMTA Guadalajara Expo

Sep 10, 2017 -

Michelle Ogihara to Participate in SMTAI Round Table: “High Time to Close the Gender Gap in STEM”

Aug 30, 2017 -

Don’t Miss the SMTA Ambassador Reception during SMTAI

Aug 29, 2017 -

Seika Machinery, Inc.’s Michelle Ogihara to Chair MSD Council Meeting at SMTAI

Aug 26, 2017 -

New Malcom SPS-2000 Solder Paste Mixer at SMTAI

Aug 26, 2017 -

Attend the 8th Annual SMTA Women’s Leadership Program at SMTAI

Aug 15, 2017 -

Seika to Bring the Industry’s Top Manufacturing Equipment to SMTAI

Jun 29, 2017 -

Seika Introduces Sayaka Twin Table PCB Router with Online Camera for Programming

May 03, 2017 -

Effectively Test Wetting Balance of Component Leads with the New MALCOM SWB-2 Dip Wetting Tester

193 more news from Seika Machinery, Inc. »

Oct 19, 2017 -

Juki Automation Systems Awards Quantum Systems ‘Representative of the Year –Best Performance’

Oct 19, 2017 -

Logic PD to Exhibit Medical Market Successes at MD&M Minneapolis 2017

Oct 18, 2017 -

Horizon Sales Earns Juki Sales Awards

Oct 18, 2017 -

MarTec Receives Outstanding Achievement Award from Juki Automation Systems

Oct 18, 2017 -

Engineered Material Systems Introduces New UV-Cured Adhesive for Bonding Lens Holders in Camera Modules

Oct 18, 2017 -

Keith Bryant to Present on Behalf of YXLON International at productronica

Oct 18, 2017 -

Metcal makes strategic move in industrial ingenuity – Learn more at productronica

Oct 18, 2017 -

Sono-Tek to Introduce New SelectaFlux-A System at productronica 2017

Oct 18, 2017 -

Aegis Software Brings “The Smarter Perspective” on Industry 4.0 MES Technology to Productronica

Oct 18, 2017 -

IPC Hand Soldering Competition Winner Crowned at IFTEC in Paris

See electronics manufacturing industry news »

Seika to Highlight Leading Equipment at SMTAI 2009 news release has been viewed 774 times

PCB machines

PCB equipment