SMT, PCB Electronics Industry News

SMT, PCB Electronics Industry News

News from BPM Microsystems


BPM to Highlight Flashstream Flash Vector Programming System at APEX 2009

Mar 10, 2009

HOUSTON � February 2009 � BPM announces that it will exhibit its manual Flashstream Flash Vector Programming System in booth 2635 at the upcoming APEX 2009 exhibition and conference, scheduled to take place March 31-April 2, 2009 in Las Vegas.

Flashstream offers the fastest flash programming of NAND and NOR flash memory at speeds as low as 2.5 percent over theoretical programming minimum. This industry leading speed is due to the creation of a proprietary co-processor technology developed by BPM called Vector Engine. This technology uses a proprietary co-processor design to hardware accelerate flash memory waveforms during the programming cycle. Faster speeds are achieved through synchronous operations that eliminate the dead times when the DUT waits on the programmer. The result is programming near the theoretical limits of the silicon design � the faster the device, the faster the device is programmed.

Designed for high-density flash, the Flashstream programs NAND and NOR Flash up to 32 Gb (gigabit) and has upgradeable RAM for future densities. It comes standard with 4191 Mb (32.7 Gb) memory per site that is upgradeable to handle future densities and communicates with USB 2.0 between the host PC and programmer. The programmer also includes bad block replacement scheme for NAND and low voltage support. A four-socket manual system, Flashstream is BPM's first dedicated hardware design for flash memories, which results in a radical improvement in speed when compared to competitive flash programmers.

As an additional benefit, multiple Flashstream units can be connected to one computer to run the same programming job in concurrent programming� mode. Single units can be mechanically connected. Also, a LED display identifies the programmer number that corresponds to software instructions.

Featuring the capability to program with one, two, three or four socket cards, the Flashstream offers the only single socket card purchase for first article qualification. It is easy to remove and stores with little space. Additionally, it includes Active, Pass and Fail LED status indicators on each individual socket card, as well as the option of Auto-start on continuity check.

Flashstream will significantly help the production of embedded designs in electronic products by reducing ramp to volume production fears for products that integrate high-density flash memory such as wireless devices, navigation electronics and personal music systems. Now, it enables new applications, especially for very large patterns. Additionally, these systems can leave the factory with preloaded data or content instead of blank memory.

The Flashstream programmer has the capacity to support NAND and NOR flash memory devices as well as EPROMs. New device requests will be taken for Flashstream and distributed to all Flashstream customers under software contract.

The Flashstream's significant speed reduces labor costs as well as the number of machines needed to perform the same function. The programmer is ready for both today's and tomorrow's most demanding flash devices.

About BPM Microsystems

Established in 1985, BPM Microsystems is a global supplier of electronic device programmers for all applications. The company is the leading supplier of vision-based automated programming systems and sets the standard in device support, performance, ease-of-use, and cost-of-ownership. The company offers a wide variety of device programmers including Universal Programmers, Concurrent Programming Systems� and Fine-Pitch Automated Programming Systems.

BPM Microsystems' financial statements are audited by Price Waterhouse Coopers LLP. BPM Microsystems is located at 5373 West Sam Houston Pkwy N, Suite 250, Houston, Texas USA 77041-5160. BPM Microsystems can be found on the Internet at http://www.bpmmicro.com.

You must be a registered user to talk back to us.

More News from BPM Microsystems

Nov 15, 2013 -

BPM Microsystems Launches 3800-MK2 Automated Programming System

Oct 28, 2013 -

BPM Microsystems Now Supports Lattice’s iCE40 Family of FPGAs

Sep 24, 2013 -

Adaptsys to Show BPM Microsystems’ High-Speed Device Programmers at ENOVA Paris

Aug 13, 2013 -

BPM Microsystems Sets the Standard in Device Programming with BPWin v5.34.0 Software Release

Jun 03, 2013 -

BPM Microsystems Releases Device-Driven Serialization White Paper

May 21, 2013 -

New Software Feature from BPM Microsystems Improves Tape Loader Teaching Process

May 16, 2013 -

BPM Microsystems to bring its 8th Generation universal device programmers to DAC 2013

May 15, 2013 -

BPM Microsystems Improves Traceability with New Laser Marker Software Feature

Mar 27, 2013 -

BPM Microsystems’ 2800 Universal Device Programmer on Display at SMT Hybrid Packaging 2013

Mar 18, 2013 -

BPM Microsystems’ Cutting-Edge Technology to be Displayed at DESIGN West 2013

(82) more news from BPM Microsystems

BPM to Highlight Flashstream Flash Vector Programming System at APEX 2009 news release has been viewed 650 times

Boundary Scan

SMT in-printer dispensing