Electronics Manufacturing Technical Articles

To Quantify a Wetting Balance Curve

Oct 19, 2017 | Frank Xu Ph.D., Robert Farrell, Rita Mohanty Ph.D.

Wetting balance testing has been an industry standard for evaluating the solderability of surface finishes on printed circuit boards (PCB) for many years. A Wetting Balance Curve showing Force as a function of Time, along with the individual data outputs "Time to Zero" T(0), "Time to Two-Thirds Maximum Force" T(2/3), and "Maximum Force" F(max) are usually used to evaluate the solderability performance of various surface finishes. While a visual interpretation of the full curve is a quick way to compare various test results, this method is subjective and does not lend itself readily to a rigorous statistical evaluation. Therefore, very often, when a statistical evaluation is desired for comparing the solderability between different surface finishes or different test conditions, one of the individual parameters is chosen for convenience. However, focusing on a single output usually doesn't provide a complete picture of the solderability of the surface finish being evaluated.

In this paper, various models here-in labeled as "point" and "area" models are generated using the three most commonly evaluated individual outputs T(0), T(2/3), and F(max). These models have been studied to quantify how well each describes the full wetting balance curve. The solderability score (S-Score) with ranking from 0 to 10 were given to quantify the wetting balance curve as the result of the model study, which corresponds well with experimental results....

Publisher: Enthone

High Reliability and High Temperature Application Solution - Solder Joint Encapsulant Paste

Oct 16, 2017 | Dr. Mary Liu and Dr. Wusheng Yin

The miniaturization and advancement of electronic devices have been the driving force of design, research and development, and manufacturing in the electronic industry. However, there are some issues occurred associated with the miniaturization, for examples, warpage and reliability issues. In order to resolve these issues, a lot of research and development have been conducted in the industry and university with the target of moderate melting temperature solder alloys such as m.p. 280°C. These moderate temperature alloys have not resolve these issues yet due to the various limitations. YINCAE has been working on research and development of the materials with lower temperature soldering for higher temperature application. To meet this demand, YINCAE has developed solder joint encapsulant paste to enhance solder joint strength resulting in improving drop and thermal cycling performance to eliminate underfilling, edge bonding or corner bonding process in the board level assembly process. This solder joint encapsulant paste can be used in typical lead-free profile and after reflow the application temperature can be up to over 300C, therefore it also eliminates red glue for double side reflow process. In this paper, we will discuss the reliability such as strength of solder joints, drop test performance and thermal cycling performance using this solder joint encapsulant paste in detail. ...

Publisher: YINCAE Advanced Materials, LLC.

Mitigation of Pure Tin Risk by Tin-Lead SMT Reflow- Results of an Industry Round-Robin

Oct 12, 2017 | David Pinsky - Raytheon Integrated Defense Systems, Tom Hester - Raytheon Space and Airborne Systems, Dr. Anduin Touw - The Boeing Company, Dave Hillman - Rockwell Collins

The risk associated with whisker growth from pure tin solderable terminations is fully mitigated when all of the pure tin is dissolved into tin-lead solder during SMT reflow. In order to take full advantage of this phenomenon, it is necessary to understand the conditions under which such coverage can be assured. A round robin study has been performed by IPC Task group 8-81f, during which identical sets of test vehicles were assembled at multiple locations, in accordance with IPC J-STD-001, Class 3. All of the test vehicles were analyzed to determine the extent of complete tin dissolution on a variety of component types. Results of this study are presented together with relevant conclusions and recommendations to guide high reliability end-users on the applicability and limitations of this mitigation strategy....

Publisher: Raytheon

Intermetallic Compounds In Solar Cell Interconnections Including Lead-Free, Low Melting Point Solders

Oct 05, 2017 | Torsten Geipel, Achim Kraft, Ulrich Eitner - ISE, Monja Moeller - Kiel University

Intermetallic compounds (IMC) in solder bonds are commonly considered critical for the reliability of interconnections. The microstructure and thermal aging characteristics of solder bonds of crystalline silicon solar cells are investigated, whereby two solders, Sn60Pb40 and a lead-free, low melting point alternative Sn41Bi57Ag2 are considered....

Publisher: Fraunhofer Insitute for Solar Energy Systems ISE

An Investigation into the Use of Nano-Coated Stencils to Improve Solder Paste Printing with Small Stencil Aperture Area Ratios

Sep 28, 2017 | Jasbir Bath, Tony Lentz, Greg Smith

These nano-coatings also refine the solder paste brick shape giving improved print definition. These two benefits combine to help the solder paste printing process produce an adequate amount of solder paste in the correct position on the circuit board pads. Today, stencil aperture area ratios from 0.66 down to 0.40 are commonly used and make paste printing a challenge.

This paper presents data on small area ratio printing for component designs including 01005 Imperial (0402 metric) and smaller 03015 metric and 0201 metric chip components and 0.3 mm and 0.4 mm pitch micro BGAs....

Publisher: FCT ASSEMBLY, INC.

Flex Circuit Manufacturing for Innovative Product Design

Sep 27, 2017 | Tuan Tran

Flex and rigid flex circuits have become increasingly popular in the high-density electronics industry for their cost-saving three-dimensional configurations. The ability to build circuitry to fit the device instead of the other way around, offers significant advantages for complex aerospace, military, and medical device applications....

Publisher: Power Design Services

Laser Wire Stripping for Medical Device Manufacturing Applications

Sep 25, 2017 | Pete Doyon, VP, Product Management, Schleuniger, Inc.

Laser wire stripping was developed by NASA in the 1970s as part of the Space Shuttle program. The technology made it possible to use smaller sized wires with thinner insulations, without risk of the damage that can be caused by traditional mechanical wire stripping methods. Laser wire stripping technology was commercialized in the 1990s and was initially used for aerospace and defense applications. Laser wire stripping then grew significantly when the consumer electronics market exploded as lasers became the only stripping solution for the tiny data cables found in laptops, mobile phones and other consumer electronics products. Another large industry that has adopted laser wire stripping methods, and for good reason, is high-end medical device manufacturing. ...

Publisher: Schleuniger, Inc.

2.5D and 3D Semiconductor Package Technology: Evolution and Innovation

Sep 14, 2017 | Vern Solberg

The electronics industry is experiencing a renaissance in semiconductor package technology. A growing number of innovative 3D package assembly methodologies have evolved to enable the electronics industry to maximize their products functionality. By integrating multiple die elements within a single package outline, product boards can be made significantly smaller than their forerunners and the shorter interconnect resulting from this effort has contributed to improving both electrical performance and functional capability. (...)

This paper outlines both positive and negative aspects of current 3D package innovations and addresses the challenges facing adopters of silicon and glass based interposer fabrication. The material presented will also reference 3D packaging standards and recognize innovative technologies from a number of industry sources, roadmaps and market forecasts....

Publisher: Vern Solberg - Solberg Technical Consulting

The Relationship Between Energy-Resource Depletion, Climate Change, Health Resources and the Environmental Kuznets Curve: Evidence From the Panel of Selected Developed Countries

Sep 13, 2017 | Syed Abdu lRehman Khan, Khalid Zaman, YuZhang

The objective of the study is to examine the relationship between energy-resource depletion, climate change, health resources and the Environmental Kuznets Curve(EKC) under the financial constraint environment in the panel of selected developed countries, over the period of 2000–2013....

Publisher: Changan University

Challenges on ENEPIG Finished PCBs: Gold Ball Bonding and Pad Metal Lift

Sep 07, 2017 | Young K. Song and Vanja Bukva

As a surface finish for PCBs, Electroless Nickel/Electroless Palladium/Immersion Gold (ENEPIG) was selected over Electroless Nickel/Immersion Gold (ENIG) for CMOS image sensor applications with both surface mount technology (SMT) and gold ball bonding processes in mind based on the research available on-line. Challenges in the wire bonding process on ENEPIG with regards to bondability and other plating related issues are summarized....

Publisher: Teledyne DALSA