Printed Circuit Board Assembly & PCB Design SMT Electronics Assembly Manufacturing Forum

Printed Circuit Board Assembly & PCB Design Forum

SMT electronics assembly manufacturing forum.


need all

tony

#26545

need all | 9 December, 2003

i need an pick-and-place, printer MPM , and so on to do SMT -production where i can find the price ol all?

tanks

reply »


G S

#26546

need all | 9 December, 2003

#26547

need all | 10 December, 2003

we have several used SMT equipment available. Please contact us at k.juchert@rohleff-consulting.com

Thanks Karsten

reply »

#26582

need all | 12 December, 2003

Hello, We sell only MPM screen printers, and they all carry warranty's. We also give training and support on MPM printers. If we can be of help just ask. http://www.geocities.com/valuems

reply »

ex maintain leader

#26587

need all | 13 December, 2003

#26588

need all | 13 December, 2003

After you get your prices, list the stuff here and get some performance, rather than price feedback on what you are looking to buy. Consider what you need to place and make sure the equipment matches it. If your doing 16mil T-Sops you wont be happy with most low end equipment and would be better off spending the money now, if your doing chips only you dont want to pay to much.

reply »

#26596

need all | 14 December, 2003

#26597

need all | 14 December, 2003

go to http://www.smtsales.com

607-535-4044 Tel. 607-535-3141 Fax. sales@smtsales.net

reply »

#26680

need all | 19 December, 2003

Tony--Good morning. We deal in used and refurbed equipment and have a nice Panasonic line available now w/ DEK 265 printer, Pana PFA MV2CXL chip shooter w/ +(130) feeders, Pana MPA3F w/ +(60) feeders, BTU VIP 70 Reflow, several pieces of input and buffer conveyors. Beautiful condition, well maintained, low hours, still plugged in and viewable, in Illinois. Customer owner is looking for bids. Call me @ (262) 249-0808. Thanks, Nick Haviland, Electronic Assembly Machinery Exchange.

reply »

TL IPS

#26686

need all | 19 December, 2003

Hi Tony,

Are you looking for new or pre-owned equipment? And are you doing any BGA and CSP work? This will be important in deciding some of the equipment that you will need.

Todd

reply »

RicardoF

#26702

need all | 22 December, 2003

Get in touch with NEA, they can Include: Insyalling, warranty, even support www.neainc.com

regards

reply »

RicardoF

#26703

need all | 22 December, 2003

Get in touch with NEA, they can Include: Installing, warranty, even support www.neainc.com

regards

reply »

odody

#26705

need all | 22 December, 2003

Tony, Be very careful with used equipment dealers. Make suer they have a comprehensive remanufacturing plan for the equipment, that it is calibrated the same as it would be from the OEM, and that the staff that will install and maintain it are familar with that specific brand of equipment. Having been burnt in the past by some of them (including some mentioned in the replies here) I cannot stress the importance of making sure the above is followed and ensured. There is nothing worse than getting a piece of equipment, finding out that it has a problem, and that the vendor is unable and/or unwilling to correct it. A used piece of equipment can end up costing far more than the initial price, especially when your depending on it for your production.

I am not saying you should not get used equipment, just make sure the vendor is capable of supporting what you buy after delivery, and that it will meet or exceed OEM specs.

reply »

Mark

#26711

need all | 23 December, 2003

Hi Tony,

Contact Universal Instruments Remanufactured Machine Divsion at 607-779-5143. They have a full line of remanufactured SMT equipment from printers-placement-reflow ovens. These machines are sold and supported by the OEM and include warranties & install.

reply »

Non-heated dispensing system

SMT Replacement Nozzles