Printed Circuit Board Assembly & PCB Design Forum

SMT electronics assembly manufacturing forum.

SMTnet
»
Electronics Forum
»
Any PCB manufacturer can do 8 layer 1.0mm PCB with 2/2mil line?

Any PCB manufacturer can do 8 layer 1.0mm PCB with 2/2mil line?

Subscribe to Thread

We got an inquiry from US that requires high volume 8 layer ... - Jul 06, 2017 by Heros Electronics

I think most manufacturers can not make this pcb board with ... - Jul 10, 2017 by Dawson

I think most manufacturers do not meet this requirement, 2 /... - Jul 11, 2017 by youth

it's said that MADPCB is trying to manufacture this pcb prot... - Jul 13, 2017 by Dawson

Yes, Dawson! MADPCB is manufacturing the prototypes. ... - Jul 16, 2017 by Heros Electronics

out of curiosity what components on the PCBs required the de... - Jul 17, 2017 by Tsvetan Usunov

I checked, there is no BOM in the ZIP. Do you know how to up... - Jul 21, 2017 by Heros Electronics

WELLPCB PTY LTD is an Australia daughter company of Uniwell ... - Jul 24, 2017 by Shaukat Ali

> We got an inquiry from US that requires high > vol... - Jul 24, 2017 by Dawson

almost can do that. If you have this require, you can refer... - Jul 29, 2017 by Benny LI

Heros Electronics

#78100

Any PCB manufacturer can do 8 layer 1.0mm PCB with 2/2mil line? | 6 July, 2017

We got an inquiry from US that requires high volume 8 layer 1.0mm PCB, OSP + selective ENIG surface, 5 groups impedance control, and stacked vias. These requirements are common, but there is 2/2mil lines in inner layers. It's said that this order was produced in foxconn. Any PCB manufacturer can do it? no matter from China mainland or other area or country. Thanks!

reply »

Dawson

#78175

Any PCB manufacturer can do 8 layer 1.0mm PCB with 2/2mil line? | 10 July, 2017

I think most manufacturers can not make this pcb board with 2/2mil line in high volume since the bad rate is high. But anyway you can share your gerber files to some professional HDI PCB manufacturers, like http://www.madpcb.com.

reply »

youth

#78201

Any PCB manufacturer can do 8 layer 1.0mm PCB with 2/2mil line? | 11 July, 2017

I think most manufacturers do not meet this requirement, 2 / 2mil line is too thin, easy to disconnect

reply »

Dawson

#78377

Any PCB manufacturer can do 8 layer 1.0mm PCB with 2/2mil line? | 13 July, 2017

it's said that MADPCB is trying to manufacture this pcb prototypes for check whether they can put it into mass production.

reply »

Heros Electronics

#78417

Any PCB manufacturer can do 8 layer 1.0mm PCB with 2/2mil line? | 16 July, 2017

Yes, Dawson! MADPCB is manufacturing the prototypes.

reply »

Tsvetan Usunov

#78418

Any PCB manufacturer can do 8 layer 1.0mm PCB with 2/2mil line? | 17 July, 2017

out of curiosity what components on the PCBs required the design to go down to 2/2 mils specs?

reply »

Heros Electronics

#78468

Any PCB manufacturer can do 8 layer 1.0mm PCB with 2/2mil line? | 21 July, 2017

I checked, there is no BOM in the ZIP. Do you know how to upload the gerber file or screenshot in this forum?

reply »

Shaukat Ali

#78477

Any PCB manufacturer can do 8 layer 1.0mm PCB with 2/2mil line? | 24 July, 2017

WELLPCB PTY LTD is an Australia daughter company of Uniwell Circuits Co., Ltd, which have two modern PCB factories, founded in April, 2007. WELLPCB is focusing on online prototypes orders, to meet the requirement of High Quality, low cost, fast delivery, easy ordering from customers around the world.

https://www.wellpcb.com

reply »

Dawson

#78479

Any PCB manufacturer can do 8 layer 1.0mm PCB with 2/2mil line? | 24 July, 2017

> We got an inquiry from US that requires high > volume 8 layer 1.0mm PCB, OSP + selective ENIG > surface, 5 groups impedance control, and stacked > vias. These requirements are common, but there is > 2/2mil lines in inner layers. It's said that this > order was produced in foxconn. Any PCB > manufacturer can do it? no matter from China > mainland or other area or country. Thanks!

This HDI PCB prototypes have succeed yesterday. I'm proud I have a chance to review the working gerber in the MI department. MAD PCB proved their processing capacity and confirmed they can manufacture this 4+n+4 pcb in high volume.

* 18 groups controlled impedance with single-sided and diff. * 1.8, 2.1, 2.2, 2.3, 2.5, 2.6, 3.0 mil lines in inner &outer. * 8 BGA with via-in-pad. * staggered vias, blind vias & buried vias.

More about MADPCB, you can check http://www.madpcb.com

reply »

Benny LI

#78536

Any PCB manufacturer can do 8 layer 1.0mm PCB with 2/2mil line? | 29 July, 2017

almost can do that. If you have this require, you can refer to this website： www.allpcb.com/T2 Best price and quality, no expedite.

reply »