Printed Circuit Board Assembly & PCB Design SMT Electronics Assembly Manufacturing Forum

Printed Circuit Board Assembly & PCB Design Forum

SMT electronics assembly manufacturing forum.


Shoot Up Reflow Zone

Views: 3881

#76694

Shoot Up Reflow Zone | 8 December, 2016

We are currently experiencing with our SMD Solder Reflow Equipment on Shooting-Up Zones (Zones 3,4,5,7 & even Cooling Zone). PV exceeds about 5-10 degrees with the SP. (ex: SP=140deg, actual PV = 145deg & higher). Our equipment undergo a monthly preventive maintenance schedule. Some Blowers were already replaced, SSR and exhaust ducting. We are using a 9-Zones Reflow Oven. Please advise if somebody already experience this problem and how did you resolve it? Thank you.

reply »

#76695

Shoot Up Reflow Zone | 8 December, 2016

Make and model of reflow oven ?

reply »

#76696

Shoot Up Reflow Zone | 8 December, 2016

This is a reflow of vitronic brand,is this correct?

reply »

#76698

Shoot Up Reflow Zone | 8 December, 2016

> We are currently experiencing with our SMD Solder > Reflow Equipment on Shooting-Up Zones (Zones > 3,4,5,7 & even Cooling Zone). PV exceeds about > 5-10 degrees with the SP. (ex: SP=140deg, actual > PV = 145deg & higher). Our equipment undergo a > monthly preventive maintenance schedule. Some > Blowers were already replaced, SSR and exhaust > ducting. We are using a 9-Zones Reflow Oven. > Please advise if somebody already experience this > problem and how did you resolve it? Thank you.

So the zone set value is 140C but the board reached 145C? Sounds like the thermocouple reading 140C is not calibrated so the actual air / n2 temperature is higher. If air temperature was in fact 140C at the board level then it cannot be heated to a higher temperature. If anything it will be 5 -15 degrees cooler.

reply »

#76699

Shoot Up Reflow Zone | 8 December, 2016

We are using Heller 1809EXL, 9-Zones.

reply »

#76700

Shoot Up Reflow Zone | 8 December, 2016

Hello SteveO, Yes you are right, the board reach up to 145 deg. 5 deg higher than the set value.

reply »

#76704

Shoot Up Reflow Zone | 9 December, 2016

Hold on Carlo,

You are saying two different things, you are saying "(Zones 3,4,5,7 & even Cooling Zone). PV exceeds about 5-10 degrees with the SP. (ex: SP=140deg, actual PV = 145deg & higher). "

Then you say: "the board reach up to 145 deg. 5 deg higher than the set value"

That doesn't make sense.

reply »

#76716

Shoot Up Reflow Zone | 11 December, 2016

Hello Sr. Tech, please disregard the board temp. it should be the actual value displayed, the PV at 145 deg. while the SP @ 140deg.

reply »

#76722

Shoot Up Reflow Zone | 12 December, 2016

> Hello Sr. Tech, please disregard the board temp. > it should be the actual value displayed, the PV > at 145 deg. while the SP @ 140deg.

> Hello Sr. Tech, please disregard the board temp. > it should be the actual value displayed, the PV > at 145 deg. while the SP @ 140deg.

Hi Carlo, Please give a call to Heller service at 1-800-394-OVEN and Press 5 for Service. They will take good care of you. You can also mail to servicenj@hellerindustries.com with a screen shot of the zone setpoints and PV's and this will help them to analyze even before you call.

Best, Marc

reply »

reflow oven profiler

Reflow Oven