Printed Circuit Board Assembly & PCB Design Forum

SMT electronics assembly manufacturing forum.

SMTnet
»
Electronics Forum
»
cp743E

cp743E

Subscribe to Thread

Hello all, it has been a long time since I have visited this... - Mar 19, 2013 by vikkaraja

Don't have a CP7 but I think it has the same loader as a CP6... - Mar 20, 2013 by Sr. Tech

No I am running a single board. I already have checked few s... - Mar 20, 2013 by vikkaraja

It's most likely one of those sensors. Go into your loader I... - Mar 21, 2013 by Sr. Tech

Thanks for all the help you are giving me but I just can't p... - Mar 24, 2013 by vikkaraja

Yes, he is correct, it is probably a sensor. That does NOT m... - Mar 25, 2013 by JimmyB

Jimmy, thats the hard part. I wish I knew which sensor is ca... - Mar 25, 2013 by vikkaraja

Have you given up yet? If not, repost and I'll try to help.... - Apr 11, 2013 by JimmyB

vikkaraja

#68470

cp743E | 19 March, 2013

Hello all, it has been a long time since I have visited this forum. I am in desperate need of some help. My cp7 is giving me an err 12200066 (The X- and Y- axis have been stopped due to a (HOLD) input. It stops runing after finish running every board. And it stops at the same unloading position after transfering board to the out carrier. Has anyone seen this problem? Thank you all for your help.

reply »

Sr. Tech

#68475

cp743E | 20 March, 2013

Don't have a CP7 but I think it has the same loader as a CP643. There are about 15 different sensors that have to be made for the loader and carriers to work properly. Are you doing dual board load ?

reply »

vikkaraja

#68486

cp743E | 20 March, 2013

No I am running a single board. I already have checked few sensors that I thought might be the cause. Still no luck. I will contnue with my troublshooting. Please let me know if you think of anything that might help me with resolving my problem.

Thanks,

reply »

Sr. Tech

#68490

cp743E | 21 March, 2013

It's most likely one of those sensors. Go into your loader I/O and make sure they all change state.

reply »

vikkaraja

#68508

cp743E | 24 March, 2013

Thanks for all the help you are giving me but I just can't put my finger on this annoying problem. I checked and recheck all sensors without much sucess against the I/O. Something I am not understand is these two followning conditions--- first one I run one board and before it finishes I press Finish Current Panel. Machine runs a complete board and unloads without any problem. Second time board I just hit Start and wait until machine finish running it and unloads it. Thats when machine stops rightaway after unloading board on to the out carrier. And table is trying to go down while closing borad clamps. It errors out and gives 12200066 and Starts Trace Log Output To CP7. Thanks for any additional comments.

reply »

JimmyB

#68516

cp743E | 25 March, 2013

Yes, he is correct, it is probably a sensor. That does NOT mean a sensor is bad, just that it has not been activated during a time limit or servo count. Watch what the last 2 or 3 things it does before the error.

reply »

vikkaraja

#68522

cp743E | 25 March, 2013

Jimmy, thats the hard part. I wish I knew which sensor is causing it. There are so many sensors it's very hard to narrow it down to a specific one. I have not given up yet.

Thanks,

reply »

JimmyB

#68673

cp743E | 11 April, 2013

Have you given up yet? If not, repost and I'll try to help.

reply »